Sears CRAFTSMAN 944.621574 Скачать руководство пользователя страница 5

Страница: 5 / 36

ASSEMBLY

UNPACKING CARTON (See Fig. 2)

CAUTION: Be careful of exposed
sta ples when handling or disposing
of cartoning material.

IMPORTANT:

WHEN UN

PACK ING AND AS

SEM BLING

TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLES.

• While holding handle assembly, cut cable ties se cur ing

handle assembly to top frame. Let handle assembly
rest on tiller.

• Remove top frame of carton.
• Slowly ease handle assembly up and place on top of

carton.

• Cut down right hand front and right hand rear cor ners

of carton. Lay side carton wall down.

• Remove packing material from handle assembly.
• Separate shift rod from handle assembly.

INSTALL HANDLE (See Figs. 3, 4, and 5)

• Insert one handle lock (with teeth facing outward) in

gearcase notch. (Apply grease on smooth side of
handle lock to aid in keeping lock in place until handle
assembly is lowered into position.)

HANDLE
ASSEMBLY

SHIFT ROD

FIG. 2

HANDLE ASSEMBLY
"UP" POSITION

FIG. 4

LOOSEN HANDLE
LOCK LEVER TO
MOVE

TIGHTEN HANDLE
LOCK LEVER TO
HOLD

FIG. 3

HANDLE
ASSEMBLY

GEARCASE
NOTCH

VIEWED FROM R.H. SIDE OF TILLER

BLACK
HANDLE
LOCK

FIG. 5

HANDLE
LOCK
LEVER

FLAT
WASHER

HANDLE
LOCK

LOCK NUT

PIVOT
BOLT

GEARCASE

SLOT

REAR
CARRIAGE
BOLT

HANDLE
BASE

• Grasp handle assembly. Hold in “up” position. Be sure

handle lock remains in gearcase notch. Slide handle
assembly into position.

• Rotate handle assembly down. Insert rear carriage bolt

fi rst, with head of bolt on L.H. side of tiller and loosely
assemble locknut (See Fig. 5).

• Insert pivot bolt in front part of plate and tighten.
• Cut down remaining corners of carton and lay panels

fl at.

• Lower the handle assembly. Tighten nut on carriage

bolt so handle moves with some resistance. This will
allow for easier adjustment.

• Place fl at washer on threaded end of handle lock le-

ver.

• Insert handle lock lever through handle base and

gearcase. Screw in handle lock lever just enough to
hold lever in place.

• Insert second handle lock (with teeth inward) in the

slot of the handle base (just inside of washer).

• Raise handle assembly to highest position and se cure ly

tight en handle lock lever by rotating clockwise. Leav ing
han dle assembly in highest position will make it easier
to connect shift rod.

Содержание CRAFTSMAN 944.621574





































Результаты поиска

Содержание CRAFTSMAN 944.621574

Отзывы:

Похожие инструкции для CRAFTSMAN 944.621574

Бренды по названию

Популярные бренды

Sears CRAFTSMAN 944.621574, Руководство пользователя

Результаты поиска

Содержание CRAFTSMAN 944.621574

Отзывы:

Похожие инструкции для CRAFTSMAN 944.621574

Бренды по названию

Популярные бренды