Sears CRAFTSMAN 944.621574 Скачать руководство пользователя страница 7

Страница: 7 / 36

KNOW YOUR TILLER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER.

Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save
this manual for future reference.

FIG. 8

MEETS ANSI SAFETY REQUIREMENTS

Our tillers conform to the safety standards of the American National Standards Institute.

THROTTLE CONTROL

- Used to con trol engine speed.

SHIFT LEVER

- Used to shift transmission gears.

SHIFT LEVER INDICATOR

- Shows which gear the trans-

mis sion is in.

RECOIL STARTER HANDLE

- Used to start the engine.

CHOKE CONTROL

- Used when starting a cold engine.

DRIVE CONTROL BAR

- Used to engage tines.

DEPTH STAKE

- Controls depth at which tiller will dig.

DRAG STAKE

- Controls forward speed in forward ro tat ing

till position.

OUTER SIDE SHIELD

- Adjustable to protect small plants

from being buried.

LEVELING SHIELD

- Levels tilled soil.

DRIVE
CONTROL
BAR

THROTTLE
CONTROL

SHIFT LEVER

SHIFT LEVER
INDICATOR

RECOIL
STARTER
HANDLE

CHOKE CONTROL

DEPTH STAKE

LEVELING
SHIELD

OUTER
SIDE
SHIELD

These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their
meaning.

CAUTION

OR WARNING

TILLING

FORWARD

NEUTRAL

REVERSE

FAST

SLOW

ENGINE

OFF

OIL

FUEL

CHOKE

STOP

RUN

TILLING

DRAG STAKE

OPERATION

EP #1 GREASE

Содержание CRAFTSMAN 944.621574





































Результаты поиска

Содержание CRAFTSMAN 944.621574

Отзывы:

Похожие инструкции для CRAFTSMAN 944.621574

Бренды по названию

Популярные бренды

Sears CRAFTSMAN 944.621574, Руководство пользователя

Результаты поиска

Содержание CRAFTSMAN 944.621574

Отзывы:

Похожие инструкции для CRAFTSMAN 944.621574

Бренды по названию

Популярные бренды