SEAL 54Base Скачать руководство пользователя | Manualshive

Страница: 17 / 36

background image

Installation

7

Engl

is

h

CAUTION: Check the mains values before connecting. See section 3.4 for power
supply details. Only if absolutely necessary, use an extension cable of ample
capacity. Unroll the extension cable completely.

4.

Connect the machine to the mains using the power cable supplied with the machine. Minimum
recommended service, standard 50Hz or 60Hz, single phase 230VAC 13A with breaker not
exceeding 16A or single phase 115VAC 20A with a breaker not exceeding 20A.

WARNING:

MAKE SURE THE POWER SUPPLY CABLE AND/OR THE EXTENSION CABLE IS
NOT BLOCKING YOUR WAY AROUND THE MACHINE.

4.3 Transport

The machine can be transported on a smooth surface on its castors.

CAUTION:
Unlock front wheel before moving machine.

When moving the machine on rough surfaces or over long distances, use the original pallet
and packing material and and move it with a pallet truck or forklift.

«
...
15
16
17
18
19
...
»

Содержание 54Base





































Отзывы:

Нет отзывов

Похожие инструкции для 54Base

Бренд: D&K Group Страницы: 21

Бренд: 3M Страницы: 6

Бренд: GBC Страницы: 22

Бренд: GBC Страницы: 4

Бренд: Team Nisca Страницы: 3

Бренд: GBC Страницы: 17

Бренд: GBC Страницы: 38

Бренд: Fellowes Страницы: 4

Бренд: Advanced Greig Laminators, Inc. Страницы: 42

Бренд: Advanced Greig Laminators Страницы: 45

Бренд: Advanced Greig Laminators Страницы: 50

Бренд: Advanced Greig Laminators, Inc. Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды