Seagull Models P-26A PEASHOOTER Скачать руководство пользователя страница 4

Страница: 4 / 38

P-26A Peashooter

Instruction Manual.

Repeat this process with the other wing

panel, securely hinging the flap in place.

INSTALL THE AILERONS

CONTROL HORN.

Epoxy.

Aileron control horn.

INSTALLING THE AILERON SERVOS.

Because the size of servos differ, you

may need to adjust the size of the precut

opening in the mount. The notch in the

sides of the mount allow the servo lead to

pass through.

1) Place the servo between the mounting

blocks and space it from the hatch. Use a

pencil to mark the mounting hole loca-

tions on the blocks.

Locate the aileron, flap and elevator and

rudder control horns. The taller control horn

is used for the flaps, and the shorter horn for

the ailerons and the shortest horn for eleva-

tor and rudder.

Aileron control horn

Elevator and rudder

control horn

Flap control horn

Содержание P-26A PEASHOOTER







































Результаты поиска

Содержание P-26A PEASHOOTER

Отзывы:

Бренды по названию

Популярные бренды

Seagull Models P-26A PEASHOOTER, Инструкция по сборке

Результаты поиска

Содержание P-26A PEASHOOTER

Отзывы:

Бренды по названию

Популярные бренды