Seagull Models Magic Star 3D EP Скачать руководство пользователя страница 2

Страница: 2 / 22

MAGIC STAR 3D EP

Instruction Manual.

Thank you for choosing the

MAGIC STAR 3D EP

ARTF by

SEAGULL MODELS

COMPANY LTD

,. The

MAGIC STAR 3D EP

was designed with the intermediate/ad-

vanced sport flyer in mind. It is a semi scale airplane which is easy to fly and quick to as-

semble. The airframe is onventionally built using balsa, plywood to make it stronger

than the average ARTF, yet the design allows the aeroplane to be kept light. You will find

that most of the work has been done for you already. The motor mount has been fit-

ted and the hinges are pre-installed. Flying the

MAGIC STAR 3D EP

is simply a joy.

This instruction manual is designed to help you build a great flying aeroplane. Please read

this manual throughly before starting assembly of your

MAGIC STAR 3D EP

. User the arts

listing below to indentify all parts.

Please be awere that this aeroplane is not a toy and if assembley or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & REPONSIBILITY.

If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C

supplier and join your local R/C model Flying Club. R/C Model Flying Clubs offer a variety

of training procedures designed to help the new pilot on his way to successful R/C flight.

They will also be able to advise on any insurance and safety regulations that may apply.

INTRODUCTION.

WARNING.

KIT CONTENTS

Содержание Magic Star 3D EP























Результаты поиска

Содержание Magic Star 3D EP

Отзывы:

Похожие инструкции для Magic Star 3D EP

Бренды по названию

Популярные бренды

Seagull Models Magic Star 3D EP, Инструкция по сборке

Результаты поиска

Содержание Magic Star 3D EP

Отзывы:

Похожие инструкции для Magic Star 3D EP

Бренды по названию

Популярные бренды