Seagull Models Magic Star 3D EP Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 22

background image

WWW.SEAGULLMODELS.COM

17

2) Locate position elevator control horn.

Then, apply 2-3 drops of epoxy to the

backplate where it contacts control horn

to keep it from accidentally coming loose

in flight.

CA glue.

Epoxy.

3) Pass the Z-bend in the elevator push-

rod through the hole of the control horn.

4) Slide the pushrod into the hole in the

pushrod connector. And use side cutters

to trim the excess length of wire beyond

the connector as shown. Insert the con-

trol horn in the slot in the elevator.

Elevator control horn.

Elevator pushrod.

«
...
15
16
17
18
19
...
»

Содержание Magic Star 3D EP























Отзывы:

Нет отзывов

Похожие инструкции для Magic Star 3D EP

Бренд: M.T.H. Страницы: 2

Бренд: GAUI Страницы: 28

Бренд: GAUI Страницы: 30

Бренд: Velleman Страницы: 8

U.S. GENERAL Junior 56515

Бренд: Harbor Freight Tools Страницы: 8

Hellcat Little Nugget

Бренд: H-KING Страницы: 18

Бренд: skyangel Страницы: 16

Бренд: Eduard Страницы: 4

Бренд: Trix Страницы: 20

Бренд: Hyperflight Страницы: 12

1563W Wabash Freight Set

Бренд: Lionel Страницы: 24

Бренд: Faller Страницы: 4

Бренд: GAUGEMASTER Страницы: 4

Бренд: Teamson Kids Страницы: 20

Бренд: Arexx Страницы: 10

Christen Eagle .46

Бренд: GREAT PLANES Страницы: 36

Бренд: Nine Eagles Страницы: 14

Бренд: marklin Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды