Seagull Models Magic Star 3D EP Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 22

background image

WWW.SEAGULLMODELS.COM

11

2) While keeping the back edge of the cowl

flush with the marks, align the front of the

cowl with the crankshaft of the engine. The

front of the cowl should be positioned so the

crankshaft is in

nearly

the middle of the cowl

opening. Hold the cowl firmly in place using

pieces of masking tape.

3) Install the muffler and muffler extension

onto the engine and make the cutout in the

cowl for muffler clearance. Connect the fuel

and pressure lines to the carburetor, muffler

and fuel filler valve. Secure the cowl to fuse-

lage using the M2x8mm screws.

2x8mm

INSTALLING THE PROPELLER.

The propeller should not touch any

part of the spinner cone. If it does, use a

sharp modeling knife and carefully trim

away the spinner cone where the propel-

ler comes in contact with it.

«
...
9
10
11
12
13
...
»

Содержание Magic Star 3D EP























Отзывы:

Нет отзывов

Похожие инструкции для Magic Star 3D EP

Бренд: Hacker Страницы: 8

Бренд: Team Losi Страницы: 43

Бренд: Team Losi Страницы: 21

Бренд: QABA Страницы: 10

Ju 88C-6b Night Fighter exterior

Бренд: Eduard Страницы: 6

Battleship Tirpitz

Бренд: REVELL Страницы: 30

BATTERY BUS, SETRA S 315

Бренд: Faller Страницы: 2

E 50/BR 150 22154

Бренд: Trix Страницы: 40

Lights & Sounds

Бренд: Learning Resources Страницы: 2

Singin’ Snail Pail

Бренд: Fisher-Price Страницы: 4

Бренд: PARKZONE Страницы: 12

Бренд: PLAYTIVE JUNIOR Страницы: 20

Бренд: Gold Wing Страницы: 45

BUILDING SITE DECORATION

Бренд: Faller Страницы: 4

Бренд: LeapFrog Страницы: 13

Бренд: bruder Страницы: 2

Бренд: LEGO Страницы: 179

Kids Supemarket

Бренд: Mocka Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды