Seagull Models Magic Star 3D EP Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 22

background image

MAGIC STAR 3D EP

Instruction Manual.

8

Repeat steps to install remaining wheel

pants to the landing gear.

6) Slide the threaded end of the axle

through the hole in the bottom of the

landing gear leg. Use a washer and lock-

nut to tighten the axle to the landing gear.

Make sure to use threadlock on the nut so

it won’t vibrate loose in flight as shown.

7) Tighten the setcrews using a hex

wrench to secure the collars on the axle

over the flat spot to retain the wheel as

shown.

ELECTRIC POWER CONVERSION.

1) Locate the items neccessary to install

the electric power conversion included

with your model.

2) Recommend the items necessary to in-

stall the electric power conversion parts

included with your model.

Wheel collar.

Wheel.

M3

Axle.

Washer.

Wheel.

Wheel collar.

Washer.

nut.--

Lite-Plywood

block.

Wheel Pant.

C/A glue.

M3.

Axle.

«
...
6
7
8
9
10
...
»

Содержание Magic Star 3D EP























Отзывы:

Нет отзывов

Похожие инструкции для Magic Star 3D EP

Бренд: Laser Pegs Страницы: 2

American Superliner 3820

Бренд: Italeri Страницы: 9

SPINNER MISSILE XL

Бренд: Rage Страницы: 2

Бренд: Eduard Страницы: 4

Бренд: Eyespy Страницы: 4

Rolly FarmTrac 610.000.810.00

Бренд: Rolly Toys Страницы: 5

Бренд: Kyosho Страницы: 36

Three Rivers Fast Freight

Бренд: Lionel Страницы: 24

Big Bird Ride-On

Бренд: Playskool Страницы: 2

Бренд: Faller Страницы: 4

Бренд: Eduard Страницы: 3

Doggie Doo CORGI

Бренд: goliath Страницы: 4

Pro Racer RC71106

Бренд: Radica Games Страницы: 2

SpinX Stuntcar 2,4GHz

Бренд: Jamara Страницы: 8

Бренд: Fisher-Price Страницы: 8

Бренд: marklin Страницы: 32

SERVICING AREA ACCESSORIES

Бренд: Faller Страницы: 4

Бренд: Hasbro Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды