background image

E-2

WARNING

CAUTION

Safety Precautions

WARNING 

Situations that could result in severe injury or death. 

CAUTION

Situations that could result in property damage or
personal injury.  

Carefully observe the instruction manual for the compatible camera for this product 
before use.

This product has been designed and manufactured for use at a water depth within 
100m / 330ft. Please note that diving to a depth in excess of 100m / 330ft may 
cause damage to the product or may lead to water leakage.

Unauthorized disassembling and/or modification could result in malfunction or flooding, 
and void product warranty. Take the product to a SEA&SEA authorized service 
center for repair or inspection.

Should you notice smoke or an unusual smell coming from the product, turn it off and 
remove the batteries immediately, taking care to avoid burns. Continued operation 
could result in injury. After removing the battery, take the product to a SEA&SEA 
authorized service center for inspection.   

Discontinue use and turn the product off immediately should you notice flooding or 
leakage. 

When the product is flooding, interior pressure may build up. Please be careful when 
opening the product as water may spurt out or the cap may open explosively and 
cause injuries.  

The product has been constructed with an airtight seal. When packing the product 
for airplane travel, do not seal-up the product to alleviate pressure build up due to 
atmospheric changes.  

Do not open the product in a wet or sandy environment. Protect the interior from 
moisture and debris in order to prevent malfunction or flooding. 

Avoid strong shocks/impacts or excess stress to prevent malfunction, damage or 
breakdown. Make sure that the product has been securely mounted to other products 
in order to prevent injury, fall or missing.

Keep out of reach of children to prevent accidental ingestion. If swallowed, seek 
medical advice immediately.

Failure to heed the precautions listed below could result in serious 
consequences. To prevent injury or damage to yourself and/or others,
please observe the precautions as they contain highly important
information related to personal and product safety.

For safe handling of the product, please read the following precautions 
carefully before use.

Содержание MDX-RX100/?























Отзывы: