Sea&Sea MDX-D810 страница 20 Скачать руководство пользователя | Manualshive

Страница: 20 / 28

background image

E-19

How to use the Optional Connector

With the Optional YS Converter/N 5-pin

Connector (50123) or Optional Sync Cord

2-pin Connector (50122) installed in the

connector hole, you can connect

SEA&SEA strobe sync cords. Connect

the cord of the synchro connector to the

camera as illustrated below.

CAUTION

Attaching the Optional Accessories

This product accepts SEA&SEA optional accessories. By using this

product in combination with those accessories, you will be able to try

various shooting techniques.



Lenses, strobes and other accessories have different depth rating. Check the depth rating

for each before use.



Read the instruction manual for each accessory before use.

YS Converter/N 5-pin Connector

or

Sync Cord 2-pin Connector

Sync connector

Cord

CAUTION



When connecting the strobe connector, always refer to the instruction

manual for the YS Converter/N 5-pin Connector or Sync Cord 2-pin Connector.

«
...
18
19
20
21
22
...
»

Содержание MDX-D810





























Отзывы:

Нет отзывов

Похожие инструкции для MDX-D810

Бренд: T-Tech Страницы: 38

Бренд: 7AMEnfant Страницы: 2

Бренд: National Instruments Страницы: 11

Бренд: Unimig Страницы: 16

FireCracker CK17A

Бренд: X10 Страницы: 1

Бренд: Waycon Страницы: 8

Бренд: Wavetronix Страницы: 4

Бренд: X10 Страницы: 2

Бренд: EUROM Страницы: 28

Бренд: Zavio Страницы: 10

Бренд: Zavio Страницы: 12

Бренд: Zavio Страницы: 10

Бренд: Zavio Страницы: 32

Бренд: Zavio Страницы: 16

AquaSensors AnalogPlus 1.0

Бренд: Thermo Scientific Страницы: 24

Бренд: Hartan Страницы: 86

Бренд: LINHOF Страницы: 5

Бренд: Levana Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды