3.5
S
ECTION
3 • U
SING
Y
OUR
B
OAT
390 Sundancer
®
(
425 Sundancer
®
)
1.
Check battery solenoid
switches for ENERGIZED
position. Battery solenoid
switches are located on the
main DC breaker panel in the
bilge and the DC distribution
panel located behind an
access door in the port aft salon. (see Section
6 –
Electrical System, Fig. 6.8.1).
2.
Check the fuel tank levels.
3.
Check the oil and coolant
levels. See your Engine
Operator’s Manual for proper
readings.
4.
Check engines for coolant
drain plug installations.
5.
Check seacocks for open
position
6.
Make sure strainers are clean
and water tight (see Section
4 –
Bilge and Underwater
Gear, page 4.11).
7.
Check the bilge for fuel fumes or liquid. Do not
start the engines until the source of fumes
is determined and corrected and the bilge
area is safely ventilated.
8.
Turn on the master key
switches located on the DC
distribution panel (see
Section 6 –
Electrical
System, pg. 6.11). Listen
for alarms which indicate
ignition power.
NOTE: Ignition switches on the control station must
be in the RUN position.
9.
After ignition power is
verified, check the gear
shift lever(s) in the
NEUTRAL position and
the throttle lever(s) at
IDLE.
10. Push on the top of the
ignition switches until the
engines star t. Do not
operate starter for more than
10 seconds without allowing
starter to cool for two (2)
minutes. This will also allow the batteries to
recover between starting attempts. Once
engine has started and sufficient oil pressure
is achieved, alarm buzzer will stop.
Important: Check engine
RPM on tachometer as soon
as engine starts. Move
throttle lever down to
decrease RPM. Do not
allow RPM to exceed
1,500.
Note: Alarm will sound when:
•
Engine oil pressure is too low.
•
Engine temperature is too hot.
•
Transmission oil is too low.
•
Transmission temperature is too hot.
•
Engine stalls.
•
Exhaust temperature too high.
11. Check the oil pressure and
look at exhaust port to assure
that engine is pumping water.
12. Let the engines warm up at
idle and check for leaks. If
engine is cold, run for a short
period of time at fast idle
speed that does not exceed 1500 RPM.
SHIFT
THROTTLE
0
1
2
3
4
RPM
X1000
F/ C
0
0
PSI/kP
PSI/kP
10
E
F
1/2
F/ C
F/ C
0
0
PSI/kP
PSI/kP
280
250
175
100
100
80
60
18
14
12
10
E
F
1/2
0
40
80
140
420
Содержание 390 Sundancer
