3.5
S
ECTION
3 • U
SING
Y
OUR
B
OAT
300 Sundancer
®
(335 Sundancer
®
)
GUEST
M
AD
E IN U.S
.A
ON
OFF
FU
LL
Y E
NGA
GED AT DETEN
TS
ST
OP
ENG
INE BEFORE SWITC
HIN
G
OF
F
(
FIG
. 3.5.1)
E
F
Fuel
(
FIG
. 3.5.2)
(
FIG
. 3.5.3)
(
FIG
. 3.5.4)
(
FIG
. 3.5.5)
(
FIG
. 3.5.7)
0
80
PS/kps
40
20
60
throttle, then return to about 1/4 throttle. In cold
weather, it may be necessary to pump lever
several times before engine will start.
WARM ENGINE - Press THROTTLE ONLY
button and move shift/throttle lever about 1/4
open throttle position. Do not pump lever.
FLOODED ENGINE - press THROTTLE ONLY
button and move shift/throttle lever to full open
position. DO NOT pump lever. When the engine
starts, move shift/throttle lever back rapidly to
decrease engine speed to between 1000 and
1500 RPM.
8. TO START ENGINE:
Turn ON ignition keys on
the cabin DC distribution
panel.
9. Press engine START
switch on control station
switch panel. Do not crank
engine for more than a few
seconds if it doesn’t start.
Engine may be very cold
or flooded; see step 7.
9. After engine starts, reduce
speed to between 1000 and 1500 RPM and
check oil pressure.
10. If oil pressure is correct, let
engine warm up to normal
temperature range as
specified in the engine
manual, before shifting
into forward or reverse
gear.
3. Close engine compart-
ment and turn on battery
switch.
4. Check fuel level. Be sure
you have enough fuel for
your trip. Remember the
“1/3 Rule”: Use no more
than 1/3 of your fuel for
outbound trip; use 1/3 of
the fuel for return trip; keep
1/3 for reserve in case of
emergency.
5. Run bilge blowers for at
least 4 minutes before
attempting to start engine
Unlike your automobile
engine which is naturally
ventilated even when it is
not moving, your boat
engine compartment (the bilge) does not have
sufficient natural ventilation when the boat is not
moving or moving slowly. That is why the engine
compartment must have forced ventilation,
using the bilge blower, to remove potentially
explosive gasoline vapors, before the engine is
started and when the boat is moving slowly.
Because it may be difficult to remember to turn
on the bilge blower every time you slow down
the boat, it is recommended that the bilge blower
run all the time the engine is running.
6. Place drive unit in full DOWN/IN position.
7. Put throttle and shift
control lever into neutral;
then for a:
COLD ENGINE - press
THROTTLE ONLY button
and move shift/throttle
lever forward to full open
;;;;
;;;;
;;;;
;;;;
yyyy
yyyy
yyyy
yyyy
(
FIG
. 3.5.6)
Содержание 300 Sundancer
