Sea-Bird Electronics SBE 63 Скачать руководство пользователя страница 44

Страница: 44 / 46

Manual revision 005

Appendix IV: Replacement Parts

SBE 63

Appendix IV: Replacement Parts

Part

Number

Part

Application Description

Quantity

in SBE 63

802273 Sensor mount with

standard (XSG) connector

For mounting on and integration

with SBE 16

plus

V2,

plus

-IM V2, or 19

plus

802274

Sensor mount with

optional wet-pluggable

(MCBH) connector

For mounting on and integration

with SBE 16

plus

V2,

plus

-IM V2, or 19

plus

311133 #10-24 cap screws,

1/2” length, titanium

Secure SBE 63 in optional sensor

mount

50510 Sensor mount kit with

standard (XSG) connector

Kit includes sensor mount

(802273), clamp, and tape; for

mounting on and integration with

SBE 16

plus

V2, 16

plus

-IM V2,

or 19

plus

50511

Sensor mount kit with

optional wet-pluggable

(MCBH) connector

Kit includes sensor mount

(802274), clamp, and tape; for

mounting on and integration with

SBE 16

plus

V2, 16

plus

-IM V2,

or 19

plus

17088

Interface cable with

standard (XSG)

connectors

For integration with SBE 16

plus

V2, 16

plus

-IM V2, or 19

plus

171792

Interface cable with

optional wet-pluggable

(MCBH) connectors

For integration with SBE 16

plus

V2, 16

plus

-IM V2, or 19

plus

31450 Tygon tubing, 1/2" ID X

3/4" OD, 2 m, Black

Main plumbing for integration

with SBE 16

plus

V2, 16

plus

-IM

V2, or 19

plus

90087 Universal plumbing kit

Includes air release valve, Y-

fitting, and tubing for integration

with SBE 16

plus

V2, 16

plus

-IM

V2, or 19

plus

Note:

Previous versions of the SBE 63 had a

different hardware configuration, and

required different sensor mounts

(802096 for mount with XSG connector

and 802127 for mount with MCBH

connector, in place of 802273 and

802274). If ordering a mount for an

SBE 63 purchased previously, provide

the SBE 63 serial number so we can

verify the correct sensor mount.

Содержание SBE 63















































Результаты поиска

Содержание SBE 63

Отзывы:

Бренды по названию

Популярные бренды

Sea-Bird Electronics SBE 63, Руководство пользователя

Результаты поиска

Содержание SBE 63

Отзывы:

Бренды по названию

Популярные бренды