manualshive.com logo in svg

Sea-Bird Electronics SBE 63, Руководство пользователя

Поделиться
Скачать
Sea-Bird Electronics SBE 63 Скачать руководство пользователя страница 42

Manual revision 005 

Appendix II: Installation/Removal from Optional Sensor Mount 

SBE 63 

42 

Appendix II: Installation/Removal from 

Optional Sensor Mount 

 

 

Installation 

 

1.

 

Align the 4-pin connectors and push the SBE 63 onto the mount. 

 

2.

 

Install the two #10-24, 1/2” titanium cap screws from the back of the 

sensor mount to secure the SBE 63 in the mount. 

 

 

 

 

 

 

 

 

 

 

 

 

 

Removal 

 

1.

 

Remove the two #10-24, 1/2” titanium cap screws from the back of the 

sensor mount that secure the SBE 63 in the mount. 

 

2.

 

Pull the SBE 63 straight out of the sensor mount. If it is difficult to 

remove: 

•

 

Use a rubber glove to provide a better grip as you pull.   

OR

 

•

 

Insert 

one

 of the cap screws in the sensor mount, and thread it just 

one or two turns. Push the head of the screw with a driver; this will 

push against the housing and free the O-ring seal. Remove the cap 

screws, and then pull the SBE 63 straight out of the sensor mount. 

 

 

 

 

 

 

SBE 63 – 4-pin 

connector 

Sensor mount – 

4-pin connector 

Install 

cap 

screws 

(2) 

Содержание SBE 63















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды