
1.3.12 Safety guidelines for handling batteries
Never leave the battery close to a flame or fire.
Use only insulated tools.
Never use sulphuric acid or acid water to top up the electrolyte level.
Danger
2. Description
Figure A
1 Earth
connection
7 Recoil-starter
13 Fuel
filter
2
Oil level gauge
8
Circuit breakers
14
Air filter
3
Oil filler plug
9
Electrical sockets
15
Starter battery
4
Fuel tank plug
10
Stop lever
16
Exhaust silencer
5
Starting and shut-down key
11
Oil drain plug
6
Solenoid valve
12
Oil filter
Figure B
1
Oil gauge
3
Lower limit of gauge
5
Screw
2
Upper limit of gauge
4
Oil drain plug
6
Oil filter
Figure C
1
Fuel tank exit hose
2
Input & return hoses for the fuel
filter
3
Fuel filter screw
Figure D
1
Nut for the air filter cover
3
Wing nut
5
Paper element
2
Air filter cover
4
Foam element
6
Rubber gasket
3. Preparation before use
3.1. Positioning the generating set for operation
Choose a site that is clean, well ventilated and sheltered from bad weather.
Place the generating set on a flat, horizontal surface which is firm enough to prevent the set sinking down (under no circumstances
should the set tilt in any direction by more than 10°).
Store the additional supplies of oil and fuel within close proximity, whilst maintaining a certain distance for safety.
3.2. Earthing the generating set
The generating sets supply electrical current when in operation: risk of electrocution.
Connect the generating set to the ground at each use.
Danger
To connect the set to the ground: Attach a 10 mm
2
copper wire to the set’s earth connection and to a galvanised steel earthing rod
driven 1 meter into the ground.
3.3. Checking the oil level
Before starting the generating set, always check the engine oil level.
Top up with the recommended oil
(see § Characteristics)
using a funnel, up to the top limit of the gauge.
Allow the generating set to cool down for at least 30 minutes before checking the oil level.
Important
n
Remove the oil gauge (fig. A – No.2 & fig. B - No. 1) and wipe it.
o
Put back the oil gauge then take it out again. Visually check the level, it must be between the upper limit of the gauge (fig. B – No.
2) & the lower limit of the gauge (fig. B – No. 3).
p
Top up if necessary using a funnel.
q
Put the oil gauge back in place.
r
Check that there are no leaks.
s
Wipe off excess oil with a clean cloth.
Содержание 6500 TE
