Scout Boats 222 Abaco, Руководство пользователя

Страница: 31 / 116

31
Pressing the “Auto” side of the switch activates the automatic
float switch next to the pump. The pump moves water out
through a thru-hull fitting in the hull. The pump is also acti-
vated by an automatic float switch that is activated whenever
the batteries are connected and the bilge switch is set to “Auto.”
The pump will run as needed whenever the water in the bilge
accumulates high enough to raise the float switch to the “ON”
position and turn off when the water is removed.
Note: The bilge pump on the Sportfish and Abaco will
start automatically when there is sufficient water
in the bilge to activate the float switch. The float
switch is protected by a circuit breaker located
near the battery switch and is always supplied cur-
rent when the batteries are connected and the bilge
switch is set to “Auto.”
Bilge (Dorado)
Manually activates the aft bilge pump located in the stern
bilge near the transom. The pump moves water out through a
thru-hull fitting in the hull. The pump is also activated by an
automatic float switch that is activated whenever the batter-
ies are connected. This pump will run as needed whenever
the water in the bilge accumulates high enough to raise the
float switch to the “ON” position and turn off when the water
is removed.
Note: There is no “Auto” position on the bilge switch
on the Dorado. The bilge pump will start auto-
matically when there is sufficient water in the bilge
to activate the float switch. The float switch is
protected by a circuit breaker or fuse located near
the battery switch and is always supplied current
when the batteries are connected.
Navigation Lights
The switch is a three-position switch. The middle position is
“OFF.” Moving the switch in one direction will activate the
navigation lights. Moving the switch in the opposite direc-
tion activates the anchor light.
Interior Lights
Activates the lighting in the cabin or head compartment. The
lights in the head compartment on the Dorado and the cabin
on the Abaco can be switched on and off with the switch on
the light fixtures once they are activated by the interior light
switch.
Courtesy Lights
Activates the lights that illuminate the cockpit and helm area.
12-Volt Receptacle
Provides electrical current for portable 12-volt equipment.
Aerator Switch
Activates the livewell circulating pump that supplies water to
the livewell.
Livewell Light
Activates the light in the livewell.
Water Pressure
Activates the raw and fresh water washdown pump. The pump
is the pressure demand type. The pressure switch automati-
cally controls the water pump when the system is activated
and properly primed.
Note: Please refer to the Raw and Fresh Water Systems
chapters for more information on the livewell and
washdown systems.
Accessory Switches
Supplies current to additional equipment that may have been
installed by Scout or your Scout dealer. If no accessories are
activated by these switches, they remain wired in the panel in
reserve.
Spreader Lights (T-Top Option)
Activated by the accessory switches in the helm panel. There
are 2 switches on the Sportfish. One switch activates the aft
spreader light and one switch activates the forward spreader
light.
Additional DC Switch Panels and Circuit Breakers
Trim Tab Switch (Optional)
Located in the helm. This switch controls the trim tab planes
located on the transom of the boat. It is protected by a circuit
breaker located in the 12-volt helm switch panel. Please re-
fer to the Helm Control Systems chapter for detailed infor-
mation on the operation of the trim tab controls.
Engine Trim and Tilt Switches
Located in the helm. These switches may be installed in the
engine control handle or on the helm console, depending on
the engines or controls installed in your boat. They control
the trimming and tilting of the engines. Please refer to the
Helm Control Systems chapter and the engine owner's manual
for information regarding the proper use of the tilt and trim
switches.
Engine Key Switch
The ignition switch is a key activated, three-position switch,
which activates the engine. The switch has an off, on and
momentary start position. To start the engine, make sure the
shift lever is in the neutral position and your hand is on the
throttle lever in the idle position. Turn the switch to the start
position. When the engine starts, release the switch and it
will automatically return to the run position. Stop the engine
by turning the switch to the off position.