Scout Boats 145 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 112

background image

Scout Boats

7-3

Care and Maintenance

Never exceed the recommended fuse sizes or bypass the fuse
safeguard. Always install the proper (type and rating) fuses
whenever replacing or changing fuses. Continuous
fuse/breaker failures indicate a severe problem and requires
immediate attention. Failure to install correct fuse may result in
damage to the electrical system or severe personal injury.

Some boat models have each individual circuit protected with a circuit
breaker located next to the switch. To reset a tripped circuit breaker, switch
OFF the circuit, wait about one
minute for the breaker to cool, push
the breaker button fully, and switch
ON the circuit.

Some boat models have circuits
protected by fuses. If the fuse
should blow-out, locate the fuse
block behind the instrument panel.
Use a fuse removal/installation tool
to replace the fuse.

NOTICE

The electrical system is
designed to protect you
from short cir cuits and
overload. Any modifications
to the system, such as
adding electrical acces-
sories, should be done by a
qualified technician.

Some installed accessories,
such as the stereo, have an
additional fuse located in the
positive lead of the stereo.
Some in-line fuse holders can
be found near the battery.

!

WARNING

KC-1630

TYPICAL FUSE BLOCK

KC-1640

TYPICAL IN-LINE FUSE HOLDER

(TWIST AND PULL TO OPEN)

Scout Boats Section 7.qxd:Scout Boats Section 7.qxd 5/11/07 5:42 AM Page 3

«
...
77
78
79
80
81
...
»

Содержание 145

















































































































Отзывы:

Нет отзывов

Похожие инструкции для 145

Бренд: COBIA Страницы: 24

Classic Runabout EP RTR

Бренд: ProBoat Страницы: 4

Бренд: GALA Страницы: 10

Бренд: Williams Страницы: 57

Multi-sport Inboard Boat

Бренд: Tige Страницы: 91

Бренд: Seaboater Страницы: 55

Бренд: World Cat Страницы: 74

Бренд: World Cat Страницы: 91

Бренд: World Cat Страницы: 98

Бренд: Sea-doo Страницы: 105

Бренд: TALAMEX Страницы: 51

Бренд: Jeanneau Страницы: 96

Бренд: PATHFINDER Страницы: 35

Бренд: Kayak Innovations Страницы: 2

Бренд: Xtreme Страницы: 3

Бренд: Wayland Folding Kayaks Страницы: 9

Бренд: Wehncke Страницы: 60

Бренд: Sevylor Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды