Scout Boats 145 Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 112

background image

Scout Boats

9-3

Storage

Reactivating The Boat After Storage

●

Charge and install batteries in boat.

●

Check engine and bilge for signs of nesting animals; clean as
necessary.

●

Check entire engine for cracks and leaks caused by freeze damage.

●

Check hose condition and all hose clamps for tightness.

●

Install bilge drain plugs.

●

Perform daily maintenance. If not performed during lay-up, perform
annual maintenance.

●

If the boat is equipped with the optional fresh water cooling system
(stern drive only) and was drained for storage, fill the system with fresh
coolant solution.

●

Check and lubricate steering system.

●

Replace water separator.

●

Remove blocks from under trailer frame.

●

Tighten tie-downs and trailer winch line.

●

Check tire pressure and lug nuts on trailer.

●

Take the boat to the water and start it. It may take a minute of cranking
to allow the fuel system to prime. Allow a one minute cool down period
for every 15 seconds of cranking. When the engine starts, keep a close
watch over the gauge readings and check for leakage and abnormal
noises. Keep speeds low for the first 15 minutes until the engine has
reached normal operating temperature.

Scout Boats Section 9.qxd:Scout Boats Section 9.qxd 5/11/07 5:43 AM Page 3

«
...
91
92
93
94
95
...
»

Содержание 145

















































































































Отзывы:

Нет отзывов

Похожие инструкции для 145

Бренд: Rave Sports Страницы: 16

Бренд: Sea Eagle Страницы: 13

Бренд: Paddle King Страницы: 23

Бренд: Regal Страницы: 352

Бренд: Sea-doo Страницы: 130

Бренд: Jensen Страницы: 15

Бренд: Johnson Outdoors Страницы: 8

Бренд: Yamaha Страницы: 142

Бренд: Yamaha Страницы: 144

Бренд: Yamaha Страницы: 148

Бренд: Williams Страницы: 57

Бренд: komodo Страницы: 16

Бренд: Pelican Страницы: 2

Бренд: Sailfish Страницы: 41

MERRY FISHER 655 MARLIN

Бренд: Jeanneau Страницы: 72

Бренд: Rave Sports Страницы: 16

Бренд: BearCreeks Страницы: 17

Бренд: Sea Eagle Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды