Scout Boats 145 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 112

background image

Scout Boats

3-11

Water Pressure Gauge

Registers the water circulated by the water pump in
pounds per square inch (PSI). Use this gauge to
observe that the engine cooling system is operating
properly. Consult the engine manual for the normal
operating PSI range.

Oil Level Gauge (Oil Injection Only)

Registers the level of injection oil in the reservoir. Some
injection systems may provide an indicator on the
reservoir. Consult the engine manual for more
information.

Trim Gauge

Measures engine or stern drive tilt and indicates the
relative position of the bow, up or down when boat is on
plane. Use this gauge to monitor boat trim.

Voltmeter

Indicates the condition of the main or cranking battery
in volts DC. Normal operating range is 12+ volts.

Ammeter

Measures the charging current in the electrical
system. Consult the engine manual for the normal
operating range.

Engine Water Temperature Gauge

Indicates the water/coolant temperature inside the
engine. Consult the engine manual for the normal
operating range.

Systems, Controls & Indicators

KC-0750

16

10 13

VOLTS

-

+

50

0

50

AMP

-

+

KC-0760

10 15

24

6

5

7

8

TEMP

F x 10

0

C x 10

0

KC-0770

UP

TRIM

DN

KC-0740

WATER

PRESS

5

10

15

20

25

30

KC-0730

Scout Boats Section 3.qxd:Scout Boats Section 3.qxd 5/11/07 5:38 AM Page 11

«
...
49
50
51
52
53
...
»

Содержание 145

















































































































Отзывы:

Нет отзывов

Похожие инструкции для 145

Бренд: RS SAILING Страницы: 70

Бренд: Dehler Страницы: 39

60 Day Cruiser 2020

Бренд: YAMARIN Страницы: 100

Бренд: LaserPerformance Страницы: 10

Бренд: LaserPerformance Страницы: 15

Бренд: Mercury Страницы: 123

Бренд: Hunter Страницы: 91

Бренд: Performance Cruising Страницы: 59

Бренд: Gumotex Страницы: 8

Бренд: TAKACAT Страницы: 4

Бренд: TAKACAT Страницы: 10

Бренд: BENETEAU Страницы: 35

Бренд: Native Watercraft Страницы: 16

Narak Cross 475

Бренд: Nautiraid Страницы: 20

Бренд: Ranger Tugs Страницы: 36

SUN ODYSSEY 349

Бренд: Jeanneau Страницы: 100

2180 BAY RANGER

Бренд: Ranger Страницы: 78

PIRATE SHIP 59073

Бренд: Banzai Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды