Scott Safety SEMS II Скачать руководство пользователя

Страница: 8 / 36

Page 8 of 36

P/N 595289-01 Rev B 5/15

WARNING

THE INFORMATION BELOW IS MEANT TO

SUPPLEMENT, NOT REPLACE, THE TRAINING,

S U P E R V I S I O N , M A I N T E N A N C E , A N D

OTHER ELEMENTS OF YOUR ORGANIZED

RESPIRATORY PROTECTION PROGRAM.

SEE WARNING ON FIRST PAGE OF THIS

DOCUMENT. FAILURE TO COMPLY WITH THESE

INSTRUCTIONS MAY RESULT IN SERIOUS

INJURY OR DEATH.

WARNING

USERS OF RESPIRATORS EQUIPPED WITH

THE SEMS II DISTRESS ALARM MUST BE

AWARE OF THE PROPER OPERATION OF THE

DISTRESS ALARM. FAILURE TO RECOGNIZE

A MALFUNCTION OF THE SEMS II DISTRESS

ALARM AND TAKE PROPER CORRECTIVE

ACTION MAY RESULT IN SERIOUS INJURY OR

DEATH.

OPERATION AND USE OF THE SEMS II DISTRESS ALARM

(PASS)

ACTIVATION

Prepare the respirator for use according to the user instructions provided with the

respirator. Install the batteries in the SEMS II Sensor Module according to the BAT-

TERY INSTALLATION section of this instruction.
The SEMS II distress alarm device is automatically activated when the respirator is

pressurized by opening the cylinder valve of the respirator. To indicate activation, the

sensor module will sound 3 quick audible chirps and the green light located on the

control console will flash approximately once every three (3) seconds. The SEMS II

distress alarm is now in sensing mode.
Once activated, the SCOTT SEMS II distress alarm constantly monitors motion of

the respirator backframe. The sensor module is located on the respirator backframe

beneath the air cylinder and contains the motion sensor and the audible alarm. If the

sensor module does not sense motion of the respirator for twenty (20) seconds, the

SEMS II distress alarm will signal a pre-alarm condition. If there is still no motion of

the respirator for the next twelve (12) seconds the full alarm will sound.
The SCOTT SEMS II distress alarm will remain activated until turned OFF according

to these instructions.

THE CONTROL CONSOLE

(PRESSURE GAUGE DEPENDS ON SYSTEM PRESSURE)

RESET BUTTON

(YELLOW BUTTON)

MANUAL ALARM

BUTTON

(RED BUTTON)

CONSOLE

DISPLAY

WITHDRAW

BUTTON

(GRAY BUTTON)

EXTERNAL-

HEADS UP

DISPLAY

(HUD)

AIR-PAK X3 MODEL

CONSOLE

PASS

SIGNAL

LIGHT

Содержание SEMS II





































Результаты поиска

Содержание SEMS II

Отзывы:

Похожие инструкции для SEMS II

Бренды по названию

Популярные бренды

Scott Safety SEMS II, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание SEMS II

Отзывы:

Похожие инструкции для SEMS II

Бренды по названию

Популярные бренды