background image

Page 4

Page 4

NOTE

. Daily ice capacity is directly related to condenser air and water inlet temperature, water

temperature to make ice - and age of machine.

To keep your machine performing at its maximum capacity it is necessary to perform periodic

maintenance as outlined on Maintenance & Cleaning Section of this manual.

ice making capacity

SPECIFICATIONS

MF/MFN 88

I

mportant operating requirements:

MINIMUM

MAXIMUM

• Air temperature

10°C (50°F)

  40°C (100°F)

• Water temperature

5°C (40°F)

  35°C (100°F)

• Water pressures

1 bar

5 bar

• Electrical voltage variation

• 

voltage rating

  specified on

  nameplate

-10%

 +10%

Extended periods of operation exceeding these limitations

constitutes misuse under the terms of Scotsman

Manufacturer's Limited Warranty, resulting in a loss of

warranty coverage.

We reserve the right to make product improvement at any

time. Specifications and design are subject to change

without notice.

2500

2400

2300

2200

2100

2000

1900

1800

1700

1600

1500

K g .

°

C

10

AIR COOLED MODELS

WATER TEMPERATURE

AMBIENT

 TEMPERA

TURE

ICE PRODUCED PER 24 HRS.

32

38

32

27

21

15

10

°

C

MF 88

1900

1850

1800

1750

1700

1650

1600

1550

1500

1450

1400

1350

1300

1250

K g .

°

C

10

AIR COOLED MODELS

WATER TEMPERATURE

AMBIENT

 TEMPERA

TURE

ICE PRODUCED PER 24 HRS.

32

38

32

27

21

15

10

°

C

MFNS 88

1950

1850

1750

1650

1550

1450

1350

1250

1150

1050

950

K g .

°

C

10

AIR COOLED MODELS

WATER TEMPERATURE

AMBIENT

 TEMPERA

TURE

ICE PRODUCED PER 24 HRS.

32

38

32

27

21

15

10

°

C

MFNL 88

21

21

Содержание MF 88






















Отзывы: