Scotsman AC 106 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 39

background image

Page 39

Page 39

11. Switch ON again the machine at front master
button switch then push the PC BOARD PUSH
BUTTON for more then 2" and less of 5" to put the
machine in cleaning mode.

NOTE.

With the system in CLEANING/

RINSING mode the water pump is the only
component in operation to circulate the
cleaning solution in the entire water system.

12. Let the unit to remain in the CLEANING
mode for about 20 minutes then unplug again the
machine.

NOTE.

The amount of Cleaner and the time

needed for the cleaning of water system
depends of the water conditions.

13. Switch OFF the ice maker at master button
switch then flush out the cleaning solution from
the sump reservoir by taking off the sump plastic
cup. Once flushed out install again the sump
plastic cup.

14. Pour onto the evaporator cavity two or
three liters of clean potable water to rinse the
mold cups and the platen.

15. Switch ON again the machine. The water
pump is again in operation to circulate the water
in order to rinse the entire water system.
Do the operation as per steps 13 and 14 twice so
to be sure no more traces of descaling solution
remains into the sump.

Sanitation

NOTE. Sanitation of the water system is
recommended to be done once a month.

16. Prepare in a plastic container the sanitation
solution as per manufacturer dilution using warm
water (45-50

°

C).

NOTE. Never mix the cleaning with the
sanitising solution.

17. Follow the procedures as per cleaning (from
item 10 to item 13) just shorting the operation of
the water pump to 10 minutes.

18. Place again the evaporator cover and the
unit service panels.

19. At completion of the freezing and harvest
cycle make sure of proper texture and clearness
of the ice cubes and that, they do not have any
acid taste.

ATTENTION. In case the ice cubes are
cloudy-white and have an acid taste, melt
them immediately by pouring on them
some warm water. This to prevent that
somebody could use them.

20. Wipe clean and rinse the inner surfaces of
the storage bin.

REMEMBER.

To prevent the accumulation

of undesirable bacteria it is necessary to
sanitize every week the interior of the storage
bin.

«
...
37
38
39

Содержание AC 106








































Отзывы:

Нет отзывов

Похожие инструкции для AC 106

Бренд: 3M Страницы: 12

Бренд: Saeco Страницы: 92

Бренд: iCES Страницы: 55

Бренд: Omcan Страницы: 16

Бренд: Zojirushi Страницы: 17

Бренд: Faema Страницы: 28

Бренд: Davis & Waddell Страницы: 3

Бренд: Quadro Страницы: 20

KCM1 Chocolate Factory

Бренд: Kambrook Страницы: 6

Бренд: Marco Страницы: 34

Бренд: Wilfa Страницы: 52

Бренд: Royal Catering Страницы: 15

Бренд: Gaggia Страницы: 26

Бренд: Gaggenau Страницы: 32

Бренд: Emerson Страницы: 4

Бренд: Brother Страницы: 9

P-Touch PT-1280

Бренд: Brother Страницы: 2

Бренд: Bosch Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды