Scotsman AC 106 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 39

background image

Page 27

Page 27

G.

PUSH BUTTON OPERATION

DURING WATER FILLING PHASE
• Push for more then 2” but less then 5” the
machine enters in Cleaning Mode
• Push for more then 5” the machine by-pass
the Water Filling Phase

DURING FREEZING/HARVEST CYCLE
• Push for more then 5” during the Freezing
cycle the machine goes immediately into Harvest
• Push for more then 5” during the Harvest cycle
the machine enters immediately in the Freezing
cycle

The length of Harvest is equal to:
• 35” if Push Button is activated before -15

°

C

evaporating temperature LED activation

• As per Harvest cycle chart, if Push Button
is activated after -15

°

C evaporating

temperature LED activation (Red LED inside
PC Board ON steady)

F.

P.C. BOARD (Data processor)

The P.C. BOARD, fitted in its plastic box located
in the front of the unit, consists of two separated
printed circuits one at high and the other at low
voltage integrated with two fuses one on power
in (32mA) and one on power out (6.3 A), of four
aligned LEDS monitoring the operation of the
machine, of one extra monitoring RED LED
(blink 0

°

C - steady - 15

°

C), of one DIP SWITCH

with ten keys, of one push button, of input
terminals for the leads of the sensor probes and
input and output terminals for the leads of the ice
maker electrical wires.
The P.C. BOARD is the brain of the system and
it elaborates, through its micro processor, the
signals received from the three sensors in order
to control the operation of the different electrical
components of the ice maker (compressor, water
pump, solenoid valves, etc.).

TERMINAL
BOARD

TERMINAL
BOARD

CONDENSER

CONDENSER
SENSOR SOCKET

OPTICAL ICE LEVEL
CONTROLSENSOR
SOCKET

OPTICAL ICE LEVEL
CONTROLSENSOR
SOCKET

EPROM

MICROPROCESSOR

EPROM

TRANSFORMER

TRANSFORMER

VARISTOR

VARISTOR

RELAY

COMPRESSOR
RELAY

WATER PUMP
RELAY

WATER PUMP
RELAY

VALVES RELAY

HOT GAS, WATER
INLET AND PURGE
VALVES RELAY

EVAPORATOR

SENSOR SOCKET

TRIAC

TRIAC

RESET PUSH BUTTON

POWER

POWER

BIN FULL

BIN FULL

ALARM

ALARM

FREEZING

FUSE

FUSE

FUSE

FUSE

0

°

C-BLINKING

-13

°

C-STEADY

I/R ADJUSTER

RESISTANCE

RESISTANCE

FREEZING CYCLE

BIN FULL

POWER

TOO HI EVAP TEMP

TOO HI COND TEMP

PUSH
BUTTON

PUSH
BUTTON

H.

LED MEANING

GREEN LED ON
Unit under power

YELLOW BIN FULL LED ON
Unit shut-OFF at storage bin full
YELLOW BIN FULL LED BLINKING
Infrared beam break out

«
...
25
26
27
28
29
...
»

Содержание AC 106








































Отзывы:

Нет отзывов

Похожие инструкции для AC 106

Бренд: GGMgastro Страницы: 257

Бренд: Hoshizaki Страницы: 43

Бренд: Proline Страницы: 40

Deluxe Baker's Oven BR7

Бренд: Breville Страницы: 39

Ice Cream Maker 746-080

Бренд: Ide Line Страницы: 19

Бренд: tomado Страницы: 76

FlexBrew Universal 49930

Бренд: Hamilton Beach Страницы: 32

Бренд: Mr. Coffee Страницы: 13

DeLonghi PICCOLO XS

Бренд: Nescafe Dolce Gusto Страницы: 21

Бренд: Focus Electrics Страницы: 11

Бренд: Rancilio Страницы: 34

Бренд: La Pavoni Страницы: 8

Бренд: Anetsberger Brothers Страницы: 1

Бренд: Dash Go Страницы: 19

KCM514ER - JavaStudio Stainless-Steel Programmable Coffeemaker

Бренд: KitchenAid Страницы: 3

Бренд: KitchenAid Страницы: 32

JAVASTUDIO 4KCM511

Бренд: KitchenAid Страницы: 44

Бренд: Chef's Choice Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды