Scotsman AC 106 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 39

Scotsman AC 106 Скачать руководство пользователя страница 15

Page 15

Page 15

G. INSTALLATION PRACTICE

1.

Hand shut-off valve

2.

Water filter

3.

Water supply line (flexible hose)

4.

3/4" male fitting

5.

Vented drain

6.

Open trapped vented drain

7.

Drain fitting

8.

Main switch

9.

Power line

WARNING. This icemaker is not designed for outdoor installation and will not function in
ambient temperatures below 10

°

C (50

°

F) or above 40

°

C (100

°

F).

This icemaker will malfunction with water temperatures below 5

°

C (40

°

F) or above 35

°

C

(90

°

F).

1

2

3

4

5

6

7

8

9

8.

Have the bolts holding the compressor down

been checked to ensure that the compressor is
snugly fitted onto the mounting pads?

9.

Have the bin liner and cabinet been wiped

clean?

10. Has the owner/user been given the User
Manual and been instructed on the importance of
periodic maintenance checks?

11. Has the Manufacturer’s registration card
been filled in properly? Check for correct model
and serial number against the serial plate and
mail the registration card to the factory.

12. Has the owner been given the name and
the phone number of the authorized SCOTSMAN
Service Agency serving him?

«
...
13
14
15
16
17
...
»

Содержание AC 106








































Отзывы:

Нет отзывов