background image

 

Battery and Charging 

A Milwaukee® M18

 series rechargeable battery with a capacity of 5 A-hr is provided with the tool. It 

should be recharged with the provided charger or another compatible charger as needed. The battery 
has a built-in level indicator and should be at least at 1 bar out of 4 before starting a treatment process. 
The tool will automatically detect an error if the battery 
level is too low to start a process run. Charging a fully 
discharged battery will take about 1.5 hours. 

Using M18

™ 

compatible replacement batteries is 

acceptable. Lower or higher capacity batteries are also 
acceptable but will change the number of treatments 
before a recharge is needed. Extra-large capacity batteries 
will fit and operate the tool, but the extra weight may 
make it difficult to lift with the straps. 

The battery needs to be slid into place until it clicks into 
the locked position. Press both red tabs to release before 
sliding the battery off the mount. 

Maintenance 

Caution: Remove the battery before all maintenance and service.      

Lamp cleaning - small particulates

  

Use a canned air duster or compressed air nozzle with the lamp covers in place. 

 

Lamp cleaning 

 heavy particulates or visible debris 

1.

 

Remove a lamp cover by removing the 4 thumbscrews and by carefully sliding the cover off the 
end of the lamp 

2.

 

Wear latex or nitrile gloves to keep the lamps clean 

3.

 

Moisten a clean, lint-free cloth with isopropyl, ethyl, or denatured alcohol and wipe down the 
surface of the lamp(s) 

4.

 

Replace the lamp cover by sliding in over the lamp making sure the end of the lamp is captured 
by its holder in the end cap 

5.

 

Replace the 4 thumbscrews, finger tight 

Lamp lifetime 

Lamps are rated for 8,000 hours of continuous use, but th

e manufacture’s lifet

ime needs to be derated 

due to the high number of on/off cycles relative to run time. We recommend that the lamps be replaced 
after 6,000 hours of run time.  As an example, one 8-hour shift of operation for a year is about 2,000 
hours.

  

 

Содержание Ultra254 950















Отзывы: