manualshive.com logo in svg

SciCan Statim 2000, Руководство оператора

Поделиться
Скачать
SciCan Statim 2000 Скачать руководство пользователя страница 34

Page 34

/

6. Troubleshooting

Problem

Unit does not power 

ON

.

There is water under the machine.

Instruments do not dry.

Check that water was not spilled when refilling the
reservoir.  Make sure the plug in the drain tube is
secured.  Remove and reinsert the cassette .  
Attempt another cycle.  

Be careful.  The metal parts will be hot, and the cassette
will contain hot steam.

The cassette is leaking.  If water drips from the
underside of the unit during operation, check the
cassette seal for misalignment or damage and replace
the seal if required.  

Be careful.  The metal parts will be hot, and the cassette
will contain hot steam.

Attempt another cycle.   If it still leaks attempt another
cycle using a different cassette if possible.

If the leak persists, turn the unit 

OFF

, remove and unload

the cassette, unplug the unit, and call your dealer.

Best drying occurs when the cycle continues to
completion.  Allow the cycle to finish.  Make sure the
instruments are loaded correctly in the cassette.  
Refer to section 4.4 Preparing and Loading Instruments.

Check the unit leveling.

Check air filters and replace if dirty.

Clean the inside of the cassette and treat with Stat-Dri /
Stat-Dri Plus drying agent.  Refer to section 5.1 Cleaning
the Cassette.  

Examine the exhaust tube (tube to the waste bottle) 
for kinks.

Solution

Check that the unit is plugged into a properly
grounded outlet and that the power cord is firmly
seated at the rear of the machine.  

Try another circuit.  Power unit 

OFF

for 10 seconds

and then power 

ON

again.

Check the condition of the line circuit breaker or fuse.

Содержание Statim 2000












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды