manualshive.com logo in svg

SciCan Statim 2000, Руководство оператора

Поделиться
Скачать
SciCan Statim 2000 Скачать руководство пользователя страница 31

Page 31

/

5. Maintenance Cont’d.

Technician

Once a year

Cassette

Air Filters

Check the tray, lid and seal for damage. 
Replace if necessary.

Check the filters.  Replace if dirty.

Solenoid Valve

Inspect the valve and clean if dirty.  
Replace the plunger if defective.

Calibration

Calibrate the unit.

Pump

Clean the filters, replace if dirty.

Check Valve

Remove the air compressor tube from the check valve inlet
while running a cycle.  Make sure no steam is leaking from
the valve.  Replace if there are any leaks.

Water Reservoir

Check the reservoir for dirt.  Clean and rinse 
with steam process distilled water if necessary.

Operator

Daily

Cassette

Wash the interior of the cassette with chlorine-free
dishwashing detergent or soap.  Rinse thoroughly with water.

Unit

To ensure optimal performance of the Statim autoclave,
SciCan recommends that a full sterilization cycle, which must
include the full Air Drying phase, be completed at the end of
each day of use.  This is especially important when the unit is
left idle over the weekend or for any extended period of time.

Weekly

Waste Bottle

Empty the waste bottle every time you refill the reservoir.  
Fill with tap water up to MIN line.  You can also add some
chlorine-free disinfectant.

Every six months

Air Filter

Replace every 500 cycles or six months
(whichever comes first).

Biological Air Filter

Replace every 500 cycles or six months
(whichever comes first).

Cassette Seal

Replace every 500 cycles or six months
(whichever comes first).

Air Filter

Check the air filter for dirt and moisture.
Replace if dirty.  Call for service if wet.

Water Reservoir

Drain Daily

Biological Air Filter

Check the air filter for dirt and moisture. 
Replace if dirty.  Call for service if wet.

The schedules below describes the necessary actions.

Содержание Statim 2000












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды