manualshive.com logo in svg

Schwinn AD7 AirDyne, Руководство по обслуживанию

Поделиться
Скачать
Schwinn AD7 AirDyne Скачать руководство пользователя страница 57

57

D

E

F

G

Front end belt alignment (Fan cage not shown for clarity)

8.

  Using 13 mm wrench and 6mm hex key, loosen and remove the 

hardware (F) from the Rear Idler Pulley assembly (G). Remove the Rear 

Idler Pulley from the bracket and Drive Belt (E). Discard the old Rear Idler 

Pulley assembly.

9.

  Install the new Rear Idler Pulley (G). 

 NOTICE:

   Do not overtighten the hardware (F). The Rear Idler Pulley 

must be able to turn. If the hardware is too tight, this can 

cause wear on the bearings.

10.

  To put the Drive Belt (E) onto the Drive Pulley (D), align the grooves 

of the belt with the grooves at the top of the pulley, with the slack of the 

belt to the outside. While holding the belt on the pulley, rotate the Drive 

Pulley backward until the belt is completely seated on the pulley. Make 

sure the Drive Belt is aligned on the Fan pulley (H), Rear Idler Pulley (G) 

and Drive Pulley. 

 

   

Be sure to keep fingers clear of all pinch hazards as 

you turn the Drive Pulley.

11.

  Using a 10mm open end wrench, adjust the Tension Adjustment Nuts 

(A) to the position recorded in step 2, on both sides of the machine. 

12.

  Using the 19 mm open end wrench, tighten the Fan spindle lock nuts 

(C) on each end of the Fan shaft (K).

13.

  Reinstall the Shrouds. Refer to the “Replace the Shrouds” procedure 

in this manual.

 NOTICE:

   Be sure the tabs in the Top Shroud snap into the Main 

Assembly.

14.

  Make sure that the belt tension is correct. Refer to the “Belt Tension 

Adjustment” section in this manual.

 Note:

  This step may require two people.

15.  Final Inspection

Inspect your machine to ensure that all hardware is tight and components 

are properly assembled.

Do not use until the machine has been fully assembled and 

inspected for correct performance in accordance with the 

Owner’s Manual.

E

C

K

H

A

Содержание AD7 AirDyne
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды