SCHUNK PCFC Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 40

SCHUNK PCFC Скачать руководство пользователя страница 6

General

6

01.00 | PCFC | Assembly and Operating Manual | en | 1454631

1.1.3 Applicable documents

• General terms of business *
• Catalog data sheet of the purchased product *
The documents marked with an asterisk (*) can be downloaded on
our homepage

schunk.com

1.1.4 Variants

This operating manual applies to the following variations:
• PCFC-A-S1
• PCFC-B-S1
• PCFC-C-S1

1.2 Warranty

If the product is used as intended, the warranty is valid for 24
months from the ex-works delivery date under the following
conditions:
• Observe the ambient conditions and operating conditions
Parts touching the workpiece and wear parts are not included in
the warranty.

1.3 Scope of delivery

The scope of delivery includes
• Passive Compliant Force Control Tool PCFC in the version

ordered

• Assembly and Operating Manual
• Accessory pack

1.4 Accessories

The following accessories are available for the product, which
must be ordered separately:
• Adapter plate
• Regulator Kit
For information regarding which accessory articles can be used
with the corresponding product variants, see catalog data sheet.

«
...
4
5
6
7
8
...
»

Содержание PCFC









































Отзывы:

Нет отзывов