SCHUNK KSP plus-BWM Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 55

SCHUNK KSP plus-BWM Series Скачать руководство пользователя страница 10

Basic safety notes

10

04.00|1151449 KSPplus-BWM, KSP-LHplus-BWM |en

Notes on safe operation

Incorrect handling of the personnel

Incorrect handling and assembly may impair the product's safety

and cause serious injuries and considerable material damage.
• Avoid any manner of working that may interfere with the

function and operational safety of the product.

  •  Use the product as intended.
  •  Observe the safety notes and assembly instructions.
  •  Do not expose the product to any corrosive media. This does

not apply to products that are designed for special

environments.

  •  Eliminate any malfunction immediately.
  •  Observe the care and maintenance instructions.
  •  Observe the current safety, accident prevention and

environmental protection regulations regarding the product's

application field.

IMPORTANT!

Following a longer shutdown period (more than approx. 6 hours),

always re-tension the clamping device in order to compensate for

the setting properties of the clamping situation or possible

pressure losses and the resulting loss of clamping force.

Transport

Handling during transport

Incorrect handling during transport may impair the product's

safety and cause serious injuries and considerable material

damage.
• When handling heavy weights, use lifting equipment to lift the

product and transport it by appropriate means.

• Secure the product against falling during transportation and

handling.

• Stand clear of suspended loads.

Malfunctions

Behavior in case of malfunctions

• Immediately remove the product from operation and report

the malfunction to the responsible departments/persons.

2.9

2.10

2.11

«
...
8
9
10
11
12
...
»

Содержание KSP plus-BWM Series
























































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды