25
E
N
G
L
IS
H
Version 18.02
3.
7
Changing the Precoating liquid during operation
3.
Cleaning the precoating pump
8
a
b
The table shown below represents the indicative amounts of precoating liquid.
It was developed on tests on a a 34 x 40 cm surface, while using distilled water and brand new TP800050 nozzles. The values contain also the
amount od precoating liquid that was sprayed on the wall inside of the PRETREATmaker IV. Depending on the dilution level of the precoating
liquid and the nozzles degree of wear the values may differ by +/- 3g. Comparison tests are required each time.
Speed
Speed
Amounr sprayed
in grams
Amount sprayed
in grams
30%
35%
40%
45%
50%
55%
60%
65%
70%
75%
80%
85%
90%
95%
100%
105%
110%
115%
120%
125%
130%
135%
140%
145%
150%
50,5
44,4
39,4
35,1
31,1
28,8
25,4
24,3
18,8
19,6
18,3
17,7
15,9
~16,97
~15,47
14,7
13,6
12,15
12,5
12,75
12,4
12,4
11,15
11,7
10,7
In order to switch from precoating tank 1 to precoating tank 2 move the switch "tank change" from tank 1 to tank 2. Always flush the pump
afterwards for at least 20 seconds with the new precoating in order to properly fill the pump. To do this press the precoating button for at least 10
times.
To clean the precoating pump and pipes press the button „maintenance” and afterwards press the button „cleaning pump and pipes”. Follow the
instructions on the display. You have to clean the pump and pipes
once a week.
3.9
Adjustment the pressure of the precoating pump
To change the pressure of the precoating pump, press the button „maintenance”and afterwards press the button „precoating pump pressure”.
Changing the pressure affects the shape of the stream from the nozzles. You can increase the pressure up to 15%, or decrease the pressure to -
15%. To low pressure can cause to narrow stream. To high pressure can cause precoating splashing. After every change the test should be made.
4.
Maintenance
4.1
Maintenance of the machine’s interior
Following the completion of work, the machine's interior must be dried using soft cloth
(pictures 1 and 4)
. Dry the drawer, the table and the inside
walls of the machine. Always remove all precoating residues. Clean the carriage rails and the teflon holder / slider
(picture 5)
with WD40. To clean
the carriage rails and teflon holder/slider, please unscrew the fixing screw of the covering rail
(picture 2)
and take it off
(picture 3)
. After cleaning,
put the covering rail back on the rail and screw the fixing screw on. It must be remembered that the guide rails of the drawer should always be
greased
(picture
s
6-7)
. Those guides have to greased with water resistant grease using a brush (
picture 7
).
It prevents rusting the rails and
protects the rails against Precoating-liquid.
3
2
1
4
5
6
7
Содержание PRETREATmaker IV
