www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
GB | 29
•
Attach the workpiece supports (9) to the fixed saw
table (17) as shown in Figure 6a,b,c and push all
the way through. Secure the shafts with the retain-
ing springs to prevent them from slipping out ac-
cidentally. The fasten in the desired position with
the screw (10).
• It is possible to tilt the machine head (5) a max.
45° to the left by loosening the set screw (22), to
tilt the machine head (5) to the right to max. 45°
the safety bolt (22a) must be loosened.
8.2 Precision adjustment of the stop for crosscut
90° (Fig. 3, 5, 16)
No stop angle included.
• Lower the machine head (5) and secure using the
locking bolt (24).
• Loosen the set screw (22).
• Position the angle stop (a) between the saw blade
(7) and the rotary table (16).
• Slacken the counternut (d). Adjust the adjusting
screw (30) until the angle between the saw blade
(7) and rotary table (16) is 90°.
• Retighten the counternut (d) to secure this setting.
• Subsequently check the position of the angle indi-
cator. If necessary loosen the pointer (20) using a
Philips screwdriver, set to position 0° on the angle
scale (19) and re-tighten the retaining screw.
8.3 Precision adjustment of the stop for mitre cut
45° (Fig. 1, 3, 5, 17)
No stop angle included.
• Lower the machine head (5) and secure using the
locking bolt (24).
• Fix the rotary table (16) in the 0° position.
• Loosen the set screw (22) and use the handle (1)
to angle the machine head (5) 45° to the left.
• 45° - position angle stop (b) between the saw blade
(7) and rotary table (16).
• Slacken the counternut (c). Adjust the adjusting
screw (31) until the angle between the saw blade
(7) and rotary table (16) is precisely 45°.
• Retighten the counternut (d) to secure this setting.
8.4 Cross cut 90° and turntable 0° (Fig. 1, 2, 6, 7)
In the case of cutting widths up to approx. 100 mm it
is possible to fix the traction function of the saw with
the set screw (23) in the rear position. In this position
the machine can be operated in cross cutting mode.
If the cutting width is over 100 mm then it is neces-
sary to ensure that the set screw (23) is loose and
the machine head (5) can move.
Attention! For 90° mitre cuts, the moveable stop rail
(28) must be fixed in the inner position.
• Open the set screw (29) on the moveable stop rail
(28) and push the moveable stop rail (28) inwards.
• The moveable stop rail (28) must be locked in a
position far enough from the inner position that the
distance between the stop rail (28) and the saw
blade (7) is no more than 5 mm.
• Before making the cut, check that no collision
could occur between the stop rail (28) and the saw
blade (7).
• Tighten the set screw (29) again. (2x 8.3 +8.4)
• Move the machine head (5) to its upper position.
• Use the handle (1) to push back the machine head
(5) and fix it in this position if required (dependent
on the cutting width).
• Place the piece of wood to be cut at the stop rail
(18) and on the turntable (16).
• Lock the material with the clamping device (8) on
the fixed saw table (16) to prevent the material from
moving during the cutting operation.
• Push down the release lever (3) to release the ma-
chine head (5).
• Press the ON/OFF switch (2) to start the motor.
•
With the drag guide (23) fixed in place:
use the handle (1) to move the machine head (5)
steadily and with light pressure downwards until
the saw blade (7) has completely cut through the
work piece.
•
With the drag guide (23) not fixed in place:
pull the machine head (5) all the way to the front.
Lower the handle (1) to the very bottom by applying
steady and light downward pressure. Now push the
machine head (5) slowly and steadily to the very
back until the saw blade (7) has completely cut
through the work piece.
• When the cutting operation is completed, move
the machine head (5) back to its upper (home)
position and release the ON/OFF button (2).
Attention!
The machine executes an upward
stroke automatically due to the return spring, i.e.
do not release the handle (1) after completing the
cut; instead allow the machine head to move up-
wards slowly whilst applying light counter pres-
sure.
8.5 Cross cut 90° and turntable 0° - 45°
(Fig. 1, 6, 7)
The crosscut saw can be used to make crosscuts of
0° -45° to the left and 0° -45° to the right in relation
to the stop rail.
Attention! For bevel cuts (inclined saw head), the
moveable stop rail (28) must be fixed in the outer
position.
• Open the set screw (29) on the moveable stop
rail (28) and push the moveable stop rail (28) out-
wards.
• The moveable stop rail (28) must be locked in a
position far enough from the inner position that the
distance between the stop rail (28) and the saw
blade (7) is no more than 5 mm.
