Scheppach 4903401901, Перевод оригинального руководства пользователя

Страница: 16 / 96


www.scheppach.com /

service@scheppach.com /

+(49)-08223-4002-99 /

+(49)-08223-4002-58
16 | GB
When changing tools make sure to have all parts
cleaned.
Prepare the appropriate tool and mount it as follows:
1. Attach the lower spindle disc (16) to the spindle
(4) (fig. 2).
2. Insert the table inlays (5) into the table (fig. 3).
3. Attach the lower spindle disc (6) to the spindle
(4) (fig. 2).
4. Slide the abrasive sleeve (7) onto the rubber
sleeve (6) (fig. 5).
5. Apply the disc (13) (use the correct measure-
ments) (fig. 6).
6. Put on the hex-nut and tighten it with the hook
wrench (14). (fig. 7)
Be sure always to mount the correct parts when
changing the abrasive sleeves. The table inlays have
to be bigger than the abrasive sleeves. (fig. 8)
Note! The 13 mm abrasive sleeve is put directly onto
the spindle (4).
Table:
Abrasive
sleeve inside D
Table inlay
inside D
Spindle disc
size
13 mm 18 mm small 16 mm
19 mm 25 mm medium 20 mm
26 mm 31 mm medium 20 mm
38 mm 44 mm large 35 mm
51 mm 57 mm large 35 mm
76 mm 82 mm large 35 mm
9. Initial operation
After completing all assembly and setup work, turn
on the machine and while it idles, check that the
spindle can move faultlessly. In the case of distur-
bances, turn the machine off immediately and rectify
the cause.
Once the machine has reached its maximum revolu-
tion speed you ay start the grinding work.
Move the work piece slowly in the direction contrary
to the running direction of the grinding roll.
Do not overload the machine by too much pressure
against the grinding roll.
After finishing the grinding turn off the machine and
disconnect the main plug.
Attention!! Use dust mask, protective goggles
and vacuum extraction.
• Although having regarded all considerable rules
there may still remain not obvious remaining haz-
rds.
• Minimize remaining hazards by following the in-
structions in ”Safety Rules”, ”Use only as author-
ized” and in the entire operating manual.
8. Commissioning
m
ATTENTION!! Always disconnect the power sup-
ply before beginning any maintenance or setup work
on the machine.
Mounting belt/disc sander to work bench
If your belt/disc sander is to be used in a permanent
location, it is recommended you secure it to a work-
bench or other stable surface. When mounting the
belt/disc sander to a workbench, holes should be
drilled through the supporting surface of the work-
bench.
• Mark holes on workbench where belt/disc sander
is to be mounted using holes in the base as a tem-
plate for hole pattern.
• Drill holes through workbench.
• Place belt/disc sander on workbench aligning
holes in the base with holes drilled in the work-
bench.
• Insert bolts and tighten securely with lock washers
and hex nuts.
Clamping belt/disc sander to work bench
If your belt/disc sander is to be used as a portable
tool, it is recommended you fasten it permanently to
a mounting board that can easily be clamped to a
workbench or other stable surface.
The mounting board should be of sufficient size to
avoid tipping while belt/disc sander is in use. Any
good grade plywood or chipboard with a 3/4 in. (19
mm) thickness is recommended.
• Mark holes on board where belt/disc sander is to
be mounted.
• Follow last three steps in section Mounting Belt/
Disc Sander to Workbench.
Note! If lag bolts are used, make sure they are long
enough to go through holes in belt/disc sander base
and material the belt/ disc sander is being mounted
to. If machine bolts are used, make sure bolts are
long enough to go through holes in belt/disc sander,
the material being mounted to, and the lock washers
and hex nuts.
Connection to vacuum suction.
The use of an extraction system is recommended.
Tool changes, Fig. 2–7
m
ATTENTION!! Turn off the machine and discon-
nect the main plug.