Assembly Instructions - Schatten Design Coil Winding Machine Model B - Kit
Tools you’ll need: rubber band, small phillips head screw driver, small flat head screw driver, ruler, needle nose pliers, small adjustable
wrench, X-Acto or other sharp knife, 8" of electrical tape, wire cutter/ wire stripper, rosin core (radio/tv) solder, small soldering iron 15 to 35
watts or soldering station set to approx. 750F. Optional tools - 10 mm socket (toggle switches), 15 mm socket or wrench (power jack),
13mm or ½" wrench (speed control).
QTY
PARTS
PART NUMBER
QTY
PARTS
PART NUMBER
ASSEMBLED
KITTED PARTS
ENCLOSURE
ELECTRICS-1 BAGGED TOGETHER
1
ENCLOSURE, PRE-DRILLED
1594DSBK
1
100K WIRE WOUND SW POT w/lock washer, nut
CT3020-ND
1
IR REFLECTIVE SENSOR w/ 6" 3 conductor
wire -PRE MOUNTED TO ENCLOSURE
958
1
MOTOR w/ PULLEY
TS840
PINK BAG
CIRCUIT BOARD ASSEMBLY
ELECTRICS-2 BAGGED TOGETHER
1
SWITCH CIRCUIT BOARD
SW BD MODEL B - REV 4A
1
IR REFLECTOR Rotary Part
IR REFLECTOR
1
DIR SWITCH DPDT ON/OFF/ON
EG2414-ND
2
O-RING DRIVE BELTS 2 1/8 x 2 1/4 x 1/16
OR-034N
1
CT RESET SWITCH SP MOMENT.
432-1170-ND
1
WIRE CLIP GREY
WIRE CLIP
1
3.3 VOLT REGULATOR
296-21633-5-ND
1
2.1 mm POWER JACK
27931-134-0
1
22uf CAPACITOR -C1
P5162-ND
1
POINTER KNOB
POINTER KNOB
1
1uf CAPACITOR -C2
P5174-ND
1
COUNTER
MINI CAL 1
1
HEAT SINK
HS198-ND
MECHANICALS BAGGED TOGETHER
MOUNTING BASE
1
WINDER ARM w/ 10-24x3/8 soc set screw
ARM
1
BOARD WHITE 6" x 6" x 5/8" PRE-DRILLED
BASE
2
BEARINGS
FR4ZZ
1
MAIN SHAFT PULLEY w/8-32x3/16 soc set screw
MAIN SHAFT PULLEY
KITTED PARTS
2
1/4" COLLARS
1/4" COLLAR
CROSS FEED ASSEMBLY BAGGED
TOGETHER
MAIN SHAFT 1/4" x 4 1/4"
ALLEN KEY 5/64"
1
LIMIT SHAFT
4" STAINLESS
1
ALLEN KEY 5/64"
ALLEN KEY 3/32"
1
ALUM FLAT, STAND OFF
1/4 X3/4 X 6"
1
ALLEN KEY 3/32"
2
1/4" FLAT WASHER
1/4" FLAT WASHER
1
1/4" LOCK WASHER
1/4" LOCK WASHER
2
1/4" NUTS
1/4" NUT
WIRE
BAGGED TOGETHER
2
1/4" COLLARS
1/4" COLLAR
1
WIRE BLACK 22 GA - 12"
BLACK
1
WIRE WHITE 22 GA - 12"
WHITE
SCREWS BAGGED TOGETHER
1
WIRE RED 22 GA - 12"
RED
2
1/4 x 20 x 1" FLAT HD PAN PHIL
MACHINE TO BASE MTG
SCREWS
1
WIRE GREEN 22 GA - 12"
GREEN
2
M3 x 5 MACHINE SCREWS
MOTOR MOUNTING
SCREWS
1
RIBBON WIRE, 4 CONDUCTOR - 4"
MULTI
4
NUTS FOR TOGGLE SWITCHES
---
2
LOCK WASHERS FOR TOGGLE SWITCHES
---
2
TABBED WASHERS FOR TOGGLE
SWITCHES
---
2
#4 x 1/2" PAN PHIL STAINLESS
CROSS FEED LIMIT MTG
SCREWS
4
SELF TAPPING SCREWS - BAGGED
COVER MTG SCREWS
Rev 03-12-2013
