Schäfter+Kirchhoff S2048U3HW Скачать руководство пользователя страница 7

Страница: 7 / 34

Installation and Setup

Instruction Manual

SK22368U3TOC

shar

ed_Installation-Electric_USB3_ML.indd

2.2 Electrical Installation: Connections and I/O Signals

All

Schäfter+Kirchhoff

USB 3.0 line scan cameras can be operated with a USB 2.0 interface. Note that there might be

limitations in terms of the maximum data transfer rate. The details for your camera can be found in section

1.4 Line

Scan Camera - Specifications (p. 5)

If the power consumption of the camera exceeds 4.5 Watt (USB 3.0) or 2.5 Watt (USB 2.0), then connect an external
source to socket

Installation and Setup

Accessories

(see also

Accessories (p. 34))

• The USB 3.0 interface provides data transfer, camera control and power supply capabilities to the SK22368U3TOC

line scan camera. If you want to operate the camera in Free Run (SK Mode 0) trigger mode the USB 3.0 cable
is the only connection you have to make.

• For any kind of synchronized operation, the external trigger signal(s) must be wired to socket

. A frame-

synchronization signal and two separate line-synchronization signals can be handled. The various trigger
modes are described fully in section

Synchronization of the Image Acquisition with the Feed Rate of the

Object (p. 18)

Synchronization

Socket: Hirose series 10A, male 6-pin

Pin

Signal

Pin

Signal

Line Sync B

Line Sync A

Frame Sync

GND

Line Sync A/B and Frame Sync: TTL levels

Status indicator

off

no power, check the USB link for a fault.

red

power on

green power on, firmware is loaded, camera is ready

External synchronization cable SK9026.x

Use this cable to feed external synchronization signals
into socket

Connectors:
Hirose plug HR10A, female 6 pin (camera side)
Phoenix 6 pin connector incl. terminal block
Cable length:
3.0 m SK9026.3

5.0 m SK9026.5

USB 3.0 cable SK9020.x

For connecting socket

with the PC or USB hub.

Cable length:
1.0 m SK9020.1

3.0 m SK9020.3 (standard)

Data and power

USB 3.0 socket type µB with threaded holes for locking screws
Power: 4.0 W

Содержание S2048U3HW



































Результаты поиска

Содержание S2048U3HW

Отзывы:

Похожие инструкции для S2048U3HW

Бренды по названию

Популярные бренды

Schäfter+Kirchhoff S2048U3HW, Инструкция по эксплуатации

Результаты поиска

Содержание S2048U3HW

Отзывы:

Похожие инструкции для S2048U3HW

Бренды по названию

Популярные бренды