Scanner Master Pro-1060, Руководство пользователя

Страница: 29 / 39

Enter the lower frequency and press ENT .
Enter the upper frequency and press ENT .
Press F1 ( Save ).
To change direction or resume searching press ▼ or ▲ .
To pause on a frequency press PSE .
To lockout a frequency press F1 ( FrL/O ).
To unlock a frequency see Unlocking Search Frequencies .
To toggle the receive mode press F2 ( Mode ).
To store a frequency into the Default Scan List press F3 ( Stor ).
To toggle the search delay on or off press FUNC then . ( DELAY ).
To toggle attenuation for the search on or off press ATT .
To toggle Zeromatic tuning on or off press FUNC then 0 .
Zeromatic Tuning
Zeromatic tuning is a feature that enhances the scanner's ability to lock on to the actual center frequency of a
search hit instead of an adjacent frequency. This option is available for all Limit, Service, and Stalker/Sweeper
search objects and dedicated searches except CB, Marine, and F/G/MURS.
Press FUNC then 0 to toggle On (uppercase Z in display) or Off (lowercase z in display) while searching .
Zeromatic On
Signal Stalker/Spectrum Sweeper Search
Contents
Your scanner's Stalker/Sweeper feature provides a powerful new tool for you to rapidly detect, monitor, and store frequencies from nearby radio
transmissions. The Stalker/Sweeper feature is more sensitive than portable frequency counters and will detect transmissions at a greater distance.
Stalker/Sweeper functions by rapidly searching through the RF spectrum in 1 MHz segments. If RF signal energy is detected in a 1 MHz segment, the
scanner will search through the 1MHz segment in finer steps until the source of the RF signal energy is found. The Stalker/Sweeper feature is similar in
functionality to portable frequency counters that cost much more than your scanner, but provides many advantages over typical portable frequency
counters. For example: The Stalker/Sweeper allows you to search the entire range of your scanner's design frequencies, or you can specify just those
frequency ranges that you wish to search.
Stalker/Sweeper Search
Special Stalker/Sweeper Search
Special Stalker/Sweeper
If a 1 MHz sweep indicates that activity is present, when set to 'On' ( F2 - SPCL ), Special Stalker/Sweeper searches the whole 1 MHz range to find the
source. If you lockout 5 frequencies within a 1 MHz segment, the scanner will skip that entire segment in subsequent searches. See SpclStalk(Sweep)Lmt
(in the ' Expert Settings ' menu) to change the (default 5 ) number of frequencies within a 1 MHz segment.
You can press F1 ( FrL/O ) when the Stalker/Sweeper stops on these undesired transmissions to prevent the Stalker/Sweeper from stopping on them in
future searches, however, the Stalker/Sweeper will still see their signal energy when searching through the 1 MHz segment. This will cause the
Stalker/Sweeper to execute another fine step search of the 1 MHz segment. If you have locked out the undesired transmissions, the Stalker/Sweeper will
not stop on them again but the overall search performance of the Stalker/Sweeper will be slowed accordingly.
Programming your
Stalker/Sweeper Sea rch as an object gives you more options for the
search (delay time, LED mode/color/latch, alarm, etc.). This will also allow you to program
different Stalker/Sweeper objects with different settings and assign them to one (or more)
of the 22 Scan Lists.
To Start a Dedicated Sweeper/Stalker Search press FUNC then SCAN/ / .
To switch between All bands or just Public Safety Bands . Press F1 ( Band ).
(Press FUNC then F1 during transmissions to override FrL/O ).
To toggle bands on or off press the number key assigned to the band.
To change direction or resume searching press ▼ or ▲ .
To pause on a frequency press PSE .
To lockout a frequency press F1 ( FrL/O ).
To unlock a frequency see Unlocking Search Frequencies .
To turn 'Special Stalker/Sweeper on or off press F2 ( spcl ). SPCL (uppercase) indicates
'Special' is active.
To store a frequency into the Default Scan List press F3 ( Stor ).
To toggle the search delay on or off press FUNC then . ( DELAY ).
To toggle attenuation for all search bands on or off press ATT .
To toggle Zeromatic tuning on or off press FUNC then 0 .
To exit press SCAN .
Notes: See also BandPlan and FlexStep settings (in the ' Expert Settings ' menu) for step
size defaults.
Priority mode is not available while using Signal Stalker/Spectrum Sweeper.
All Stalker/Sweeper Bands
Key Band Frequencies Mode
0 CB, 10m/6m Ham 25-54 Auto
1 VHF Air 108-137 Auto
2 2m Ham, PS, Rail 137-174 Auto
3 Commercial Air,1.25m Amateur 216-300 Auto
4 Military Air 300-406 Auto
5 70cm Ham, PS 406-470 Auto
6 UHF TV 470-512 Auto
7 Trunked Public Safety 764-797 Auto
8 Trunked Public Safety 806-869 Auto
9 33/23cm Ham 894-960,1240-1300 Auto
Public Safety Bands
Key Band Frequencies Mode
0 Public Safety 33.400-46.500 Auto
1 Public Safety 151-170 Auto
2 Public Safety 453-467 Auto
3 Trunked Public Safety 764-797 Auto
4 Trunked Public Safety 806-869 Auto