SCANMASKIN 32 PROPANE страница 20 Скачать руководство пользователя | Manualshive

Страница: 20 / 60

background image

20

www.scanmaskin.com

3 TRANSPORT
3.1 Precautions

Read “2.16 Safety regarding transport” before attempting to transport the machine.

.

3.2 Manual transport

• Detach the tools according to the instructions in “ 4.13 Changing tools ”.

• Push the handle downwards to lift the gear barrel about 10 cm (4”) from the ground.

• Push the machine in desired direction.

3.3 Lifting

• Before attempting to lift the machine, read “4.13 Changing tools”

• Detach the tools according to the instructions in “4.13 Changing tools”.

• Fasten the straps used for lifting at the two handles as shown in “Figure 4”.

• Lift the machine.

Figure 4

: Lifting points

3.4 Inside vehicles

• Detach the tools according to the instruction in “4.13

• Changing tools”.

• Secure the machine inside the vehicle.

«
...
18
19
20
21
22
...
»

Содержание 32 PROPANE





























































Отзывы:

Нет отзывов

Похожие инструкции для 32 PROPANE

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

BODY ARMOR PRO TERM

Бренд: Darco Страницы: 6

Бренд: DBX Bushido Страницы: 12

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Бренд: Idex Страницы: 141

Бренд: IDEAL Networks Страницы: 8

Бренд: IDEAL Networks Страницы: 5

Бренд: Tanaka Страницы: 20

Бренд: Tandem Страницы: 80

Бренд: Tanco Страницы: 4

Бренд: Yuwell Страницы: 2

FLEX-FOOT ASSURE

Бренд: Össur Страницы: 82

Бренд: Össur Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды