SCANMASKIN 32 PROPANE страница 11 Скачать руководство пользователя

Страница: 11 / 60

ENGLISH

SCANMASKIN World Series 32 Propane

www.scanmaskin.com

SAFETY REGULATIONS

Read this entire chapter carefully! Failure to comply with safety regulations may result in serious

injuries or damages.

2.1 Legend

Notation regarding safety

Notation regarding electrical safety

Notation regarding safety during transport

Tipping hazard

See reference

2.2 Safety precautions

Any machine, if it is not used according the regulations, may be hazardous for operating, set-

ting-up and service personnel. The operating authority is responsible for compliance with the

safety regulations during operation and maintenance, and for the use of safety devices

supplied with the machine, as well as the provision of appropriate additional safety devices!

Eye and ear protection must be worn at all times.

Never operate the machine when it’s not in its upright position.

Make sure there is no debris in the work area.

Check the work area for screws or other hard objects in the concrete. Don’t use the machine if there

are any foreign objects stuck into the surface. Such objects must be removed prior to operation of

machine.

R ead

“2.3 Propane safety”

and “

2.10 Safety regarding operation of machine”

thoroughly

before operation!

Содержание 32 PROPANE





























































Результаты поиска

Содержание 32 PROPANE

Отзывы:

Похожие инструкции для 32 PROPANE

Бренды по названию

Популярные бренды

SCANMASKIN 32 PROPANE, Руководство пользователя

Результаты поиска

Содержание 32 PROPANE

Отзывы:

Похожие инструкции для 32 PROPANE

Бренды по названию

Популярные бренды