SCANMASKIN 32 PROPANE Скачать руководство пользователя

Страница: 3 / 60

ENGLISH

SCANMASKIN World Series 32 Propane

www.scanmaskin.com

IMPORTANT INFORMATION!

This Manual only concerns the floor grinding machines

“SCANMASKIN 32 World Series Propane”

hereby

referred to as

“SCANMASKIN 32 WS PROPANE

”. SCANMASKIN 32 WS PROPANE may only be used for

grinding horizontal surfaces approved by Scanmaskin Sweden AB.

If SCANMASKIN 32 WS PROPANE is used for other purposes or handled in ways other than that des-

cribed in this Manual, Scanmaskin Sweden AB disclaims all responsibility.

Especially note the section

“2Safety Regulations”.

Read the Manual before using the floor grinding

machine SCANMASKIN 32 WS. The spare parts, grinding discs used on SCANMASKIN 32 WS PROPA-

NE must be approved by Scanmaskin Sweden AB.

Содержание 32 PROPANE





























































Результаты поиска

Содержание 32 PROPANE

Отзывы:

Похожие инструкции для 32 PROPANE

Бренды по названию

Популярные бренды

SCANMASKIN 32 PROPANE, Руководство пользователя

Результаты поиска

Содержание 32 PROPANE

Отзывы:

Похожие инструкции для 32 PROPANE

Бренды по названию

Популярные бренды