5
139234_Rev_A 9.17 .10
General Information
IMPORTANT: SAVE THESE INSTRUCTIONS.
1. The installation and repair of this appliance must be
done by a qualified service person. Failure to properly
install and maintain this heater could result in an
unsafe or hazardous installation, which may result in
a fire, explosion, property damage, personal injury or
loss of life.
2. This appliance should be inspected before use and
at least annually. More frequent cleaning may be
required due to excessive lint from carpeting, bedding
material, etc. It is imperative that control compart-
ments, burners and circulating air passageways of the
appliance be kept clean.
`S’assurer que le bruleur et le compartiment des com-
mandes sont propres. Voir les instructions d’installation
et d’utilisation qui accompagnent l’appareil.
3. This appliance may be installed in an aftermarket
permanently located, manufactured (mobile) home,
where not prohibited by local codes.
This appliance is only for use with the type(s) of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certified
kit is used.
Cetappareil peut être installé dans un maison préfab-
riquée (mobile) déjà installée à demeure si les règle-
ments locaux le permettent.
Cet appareil doit être utilisé uniquement avec les
types de gas indiqués sur la plaque signalétique. Ne
pas l’utiliser avec d’autres gas sauf si un kitde conver-
sion certifié est installé.
4. The installation must conform to local codes. Your lo-
cal Scan authorized dealer can assist you in determin-
ing what is required in your area for a safe and legal
installation. Some areas require a permit to install
a gas burning appliance. Always consult your local
building inspector or authority having jurisdiction to
determine what regulations apply in your area.
In the absence of local codes, the installation require-
ments must comply with the current National codes.
In the U.S., these requirements are established in the
National Fuel Code, ANSI Z223.1.(NFPA 54). In Canada,
the codes have been established in CAN/CGA B149
Fuel Installation Code.
Installer l’appareil selon les codes ou reglements
locaux, ou, en l’absence de tels reglements, selon les
Codes d’installation CAN/CGA-B149.
5. Do not operate this fireplace if any part of it has
been under water.
Immediately call a qualified service technician to
inspect the heater and to replace any part of the
control system and any gas control which has been
under water.
Ne pas se servir de cet appareil s’il a ete’ plonge dans
l’eau, completement ou en partie. Appeler un tech-
nicien qualifie pour inspecter l’appareil et remplacer
toute partie du syste’me de controle et toute com-
mande qui ont ete plonges dans l’eau.
6. Do not operate the fireplace with the glass front re-
moved, cracked or broken. Replacement of the glass
should be done by a licensed or qualified service
person. Only remove glass for routine service. Always
handle glass carefully.
Pour utilisation avec les portes en verre cerifiers aved
l’appareil seulemend ou. Ne pas utiliser avec des
portes on verre.
7. Notify your insurance company before proceeding
with installation of this fireplace.
THIS HEATER MUST BE INSTALLED AND MAIN-
TAINED BY A QUALIFIED SERVICE AGENCY.
DO NOT ATTEMPT TO ALTER OR MODIFY THE
CONSTRUCTION OF THIS APPLIANCE OR ITS COM-
PONENTS. ANY MODIFICATION OR ALTERATION
WILL VOID THE WARRANTY, CERTIFICATION AND
LISTING OF THIS APPLIANCE.
NOTE: Installation Requirements for the
Commonwealth of Massachusetts
1. If there is not one already present, on each
floor level where there are bedroom(s), a
carbon monoxide detector and alarm shall
be placed in the living area outside the
bedroom(s). The carbon monoxide detector
shall comply with NFPA 720 (2005 Edition).
2. A carbon monoxide detector shall:
a) Be located in the room that houses the
appliance or equipment;
b) Be either hard-wired or battery powered or
both; and
c) Shall comply with NFPA 720 (2002 Edition).
3. A Product-approved vent terminal must be
used, and if applicable, a Product-approved
air intake must be used. Installation shall be
in strict compliance with the manufacturer’s
instructions. A copy of the installation
instructions must remain with the appliance
or equipment at the completion of the
installation.
