SBS SBS-H2 Скачать руководство пользователя страница 12

12 

SBS-H2 Users Manual 

Rev 1.4 

January 6

th

 2013 

The information in this sheet has been carefully reviewed and is believed to be accurate; 
however, no responsibility is assumed for inaccuracies. Storage Battery Systems, LLC. 
Reserves the right to make changes without further notice to any product, datasheet, technical 
data bulletin, or website. 
 
 
Storage Battery Systems, LLC. makes no warranty, representation of guarantee regarding the 
suitability of its product for any particular purpose, nor does Storage Battery Systems, LLC. 
assume any liability arising out of the application or use of any product and specifically disclaims 
any and all liability, including without limitation consequential or incidental damages. 

“Typical” 

parameters can and do vary in different applications. All operating parameters, including 
“Typical” must be validated for each customer application by customer’s technical experts. 
 
 
Storage Battery Systems, LLC.  products are not designed, intended, or authorized for use as 
components in systems intended for surgical implant into the body, or other application intended 
to support or sustain life, or for any application in which the failure of the SBS product could 
create a situation where personal injury or death may occur. 
 
 
Should buyer purchase or use SBS products for any such unintended or unauthorized 
application, Buyer shall indemnify and hold Storage Battery Systems, LLC.  and its officers, 
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, 
and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of 
personal injury or death associated with such unintended or unauthorized use, even if claim 
alleges that Storage Battery Systems, LLC. was negligent regarding the design or manufacture 
of the part. 
 
 
In the case of a defect in the sensor, Storage Battery Systems, LLC. shall not be liable for any 
damages which may result, including, but not limited to, loss of revenue, property, or life. In any 
event, Storage Battery Systems, LLC. shall limit liability to replacement of the defective unit. 
Storage Battery Systems, LLC. does not convey any license under its patent rights nor the 
rights of others. 

 
 

 
 
 
 
 

 

 

 

N56 W16665 Ridgewood Drive 

Menomonee Falls, WI  53051 

1-800-554-2243 

 

www.sbsbattery.com

 

 

[email protected]

  

 

Pre-March 2016 Version

Содержание SBS-H2













Отзывы: