SawStop CTS-120A60 Скачать руководство пользователя страница 4

Страница: 4 / 56

GENERAL POWER TOOL SAFETY WARNINGS
Symbols

SYMBOL

DEFINITION

SYMBOL

DEFINITION

Read the instructions

min

-1

per minute

Warning of general danger

inch

Additional information or tip

lb.

pound

volts

kilogram

amperes

diameter

watt

angular degree

hertz

millimeter

alternating current

centimeter

protective earth

meter

no load speed

CFM

cubic feet per minute

rpm

revolutions per minute

LPM

liters per minute

No Warranty of Safety

It is important to understand that the safety

technology in SawStop table saws does not prevent

contact with the blade — it minimizes the effect of

the contact. If you do contact the spinning blade, the

safety technology will stop the blade, and in most

cases there will be no injury or only a small nick.

However, you may incur a serious injury on a SawStop

saw depending on factors such as the speed and

direction your hand is moving when it contacts the

blade and the type of blade you are using. Also, if

you decide to use the saw in Bypass Mode (

see page

), the safety system will be disabled and will not

activate in the event you contact the spinning blade.

Safety

A table saw is a dangerous tool and there are hazards

inherent with using this saw. Some of these hazards

are discussed in the following sections. Use common

sense when operating the saw and use the saw only

as instructed. You are responsible for your own safety.

Accessories

Use of accessories or attachments that are not

approved may result in injury and may damage the

saw.

See page 12

for a list of accessories included

with the saw. Contact SawStop Service (

see page

) if you have questions about other accessories.

See page 13

for the optional stand.

Wood Dust

Warning: Drilling, sawing, sanding or machining

wood products can expose you to wood dust, a

substance known to the State of California to

cause cancer. Avoid inhaling wood dust or use

a dust mask or other safeguards for personal

protection. For more information go to www.

P65Warnings.ca.gov/wood.

General Power Tool Safety

Warnings

WARNING Read all safety warnings, instructions,

illustrations and specifications provided with

this power tool.

Failure to follow all instructions

listed below may result in electric shock, fire

and/or serious injury.

SawStop

Compact Table Saw

Содержание CTS-120A60

























































Результаты поиска

Содержание CTS-120A60

Отзывы:

Похожие инструкции для CTS-120A60

Бренды по названию

Популярные бренды

SawStop CTS-120A60, Руководство пользователя

Результаты поиска

Содержание CTS-120A60

Отзывы:

Похожие инструкции для CTS-120A60

Бренды по названию

Популярные бренды