manualshive.com logo in svg

Savant CLI-W210, Руководство по развертыванию

Поделиться
Скачать
Savant CLI-W210 Скачать руководство пользователя страница 4

Multistat Smart Thermostat Deployment Guide (CLI-W210x/W200x) 

4   of   21 

45 Perseverance Way, Hyannis MA 02601

009-1959-00  |  200723

Savant.com

 | 508.683.2500

1.  Before You Begin

Multistat Smart Thermostat and Hardware ...................................................................................................................................................................................................................

Savant Control System running da Vinci 8.8 or higher .............................................................................................................................................................................................

HVAC system installed and appropriate wires run to the thermostat’s location(s) ......................................................................................................................................

OPTIONAL:

 Remote sensors and their associated wiring installed .....................................................................................................................................................................

Ethernet network meeting Savant requirements ........................................................................................................................................................................................................

 

See 

Appendix B: Network Requirements 

or refer to the 

Savant Device Networking Guidelines

 reference guide on the Savant Community.

Read through this document in its entirety and ensure that the following items are either available or installed before proceeding with deployment. The list 

below can be used to check off items as they are completed prior to installation.

To successfully deploy the thermostat and associated sensors, follow the steps below. Use this list to check off items as they are completed.

2.  Deployment Steps

Wire the Thermostat

1. 

Connect the HVAC Signaling Wires to thermostat. See 

Wiring Diagrams

 ...............................................................................................................................................

Blueprint Configuration

2.  Add thermostat to a Blueprint configuration. See 

Add thermostat to a Blueprint Configuration

 .................................................................................................

3.  Upload Blueprint Configuration. See 

Save Configuration, Generate Services, and Upload File

 .....................................................................................................

4.  Add Thermostat to the Local Network. See 

Wi-Fi Network

..........................................................................................................................................................................

Configure Thermostat for a standard HVAC System

5.  Use the on-screen menus to configure thermostat. See 

Basic Configuration Using the On-Screen Menus

  .............................................................................

Содержание CLI-W210






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды