manualshive.com logo in svg

Savant CLI-W210, Руководство по развертыванию

Поделиться
Скачать
Savant CLI-W210 Скачать руководство пользователя страница 20

Multistat Smart Thermostat Deployment Guide (CLI-W210x/W200x) 

20   of   21 

45 Perseverance Way, Hyannis MA 02601

009-1959-00  |  200723

Savant.com

 | 508.683.2500

Appendix B: Network Requirements

For a full overview of Savant's networking guidelines, see the 

Savant Device Networking Guidelines

 reference guide on the Savant Community

.

Network Changes

Savant recommends performing the following to refresh the IP connection after connecting to a new network, changing routers, or if the IP address range is 

changed in the current router.  This will reset any IP connection and ensure that the device is communicating with the network correctly.

From the On-Screen Display:

1.  Select the Mode icon (Off, AUTO, HEAT, COOL) at the bottom of the main window 

of the LCD display.

2.  Swipe left twice to navigate to the NETWORK window.
3.  Select the 

CHANGE

 button and in the 

Select Network To Connect

 screen that 

opens, and select the new network and follow the prompts to enter the password 

and connect to the new network.

Содержание CLI-W210






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды