Saunders M-VUE Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 32

background image

29

www.cranecpe.com

Crane ChemPharma & Energy

Technical Data

Technical Details

Valve Size Range

0.25”–2.00” (DN8-DN50)

Temperature Range

0°C to + 70°C

Sensing Technology

Continuous sensing via Hall Effect sensors
20% Tolerance

Target

Composite ferrous magnet

Stroke/Travel

3 mm (Minimum)
22 mm (Maximum)

Position Indication

Green LEDs - Open
Red LEDs - Closed
Physical position indicator

Feedback Options

24VDC P2P
AS-i version 2.0 standard address
AS-i version 2.1 extended address
AS-i version 3.0 extended address
DeviceNet

Programming

Local Programming: via magnetic key Remote
Programming: At control panel
(Networking versions only)

Standard Connection

P2P with SOV: M12 5 pin
P2P without SOV: M12 5pin
AS-i: M12 4 Pin
DeviceNet: Mini 7/8” 5 pin

Materials of Construction

Sensor Mounting Base

Glass Reinforced Polybutylene Terephthalate (PBT)

Sensor Electronics Module

Polycarbonate (PC)

Cap

Polycarbonate (PC)

Seals

Buna N (Nitrile)

Connector

Stainless steel

Fasteners

Stainless steel

Target

Composite ferrous magnet

Power Consumption

Type

PNP

24Vdc

ASi

31.5 Vdc

DeviceNet

24 Vdc

M-VUE (solenoid OFF)

< 35 mA

< 35 mA

< 40 mA

M-VUE (solenoid ON)

< 63 mA

< 70 mA

< 75 mA

Solenoid / Pneumatic Details

Optional Integral Solenoid

• Solenoid case: PBT
• Configuration: 3-Way, 2-Position, Spring Return
• Type: Direct Acting
• Voltage: 24 Vdc
• Wattage: 0.9 W
• Cv: 0.5
• Air connection: 1/8” BSP or 1/8” NPT Stainless Steele reinforced
• Optional: solenoid exhaust block

«
...
27
28
29
30
31
...
»

Содержание M-VUE

































Отзывы:

Нет отзывов

Похожие инструкции для M-VUE

Бренд: Y-cam Страницы: 12

Бренд: GE Страницы: 20

Бренд: GE Страницы: 2

Бренд: ZERO GRAVITY Страницы: 6

Бренд: NARGESA Страницы: 27

Бренд: Endress+Hauser Страницы: 28

Бренд: Back View Страницы: 168

Бренд: Jetter Страницы: 4

Бренд: K&K Страницы: 8

Бренд: K&K Страницы: 20

Бренд: K&K Страницы: 6

Бренд: K&K Страницы: 3

Бренд: K&K Страницы: 3

Бренд: UMBRA RIMORCHI Страницы: 18

Бренд: Vaisala Страницы: 2

HighLine ABF0166

Бренд: Mactronic Страницы: 2

Бренд: pleasant hearth Страницы: 6

Бренд: R&G Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды