background image

 

1-2. LCD display   

 

 

7-segment display 

 

 

: It displays each measured value. 

  Unit of wind velocity   

 

: It displays the measurement units for wind velocity   

  BF (Beaufort scale) 

  FT/M (feet/minute) 

  M/H (mile/hour) 

  KMH (kilo meter/hour) 

  M/S (meter/second) 

  KNT (knot) 

  MAX   

: Lit while the unit is in the mode for the maximum wind velocity measurement. 

  H 

 

: Lit while the measured value is hold. 

  WCl   

: Lit while the unit is in the mode for the wind chill measurement. 

  DP 

 

: Lit while the unit is in the mode for the dew point measurement. 

  WBT   

: Lit while the unit is in the mode for the wet bulb temperature measurement. 

  EXT   

: Lit while the external temperature probe is measuring the temperature. 

  Low battery 

: Lit when the battery is low and let you know to change the battery. 

  °C %rh 

: Characters of unit of temperature(°C), unit of humidity(%rh) 

 

 

2.    Installing or Replacing the Battery 

Replace the battery as follows before using the unit for the first time or when low battery is displayed. 

 

(1) Remove the battery lid by turning it counter-clockwise by using a coin or the like. 

(2) In case of replacing a battery, take out the used battery. 

(3) Insert the coin cell battery (CR2032).    Check the polar direction of positive 

and negative and place the battery correctly (Placing the battery between 

positive metal fitting and negative metal fitting) 

After  the  placement  of  the  battery,  that  of  the  positive  terminal  (+)  is 

facing upward. 

(4) Reinstall the battery lid in the reverse order of removal. 

 

 

Caution 

-  If the low battery is displayed, replace the battery immediately with a new one (CR2032). 

-  Measurements while the battery power is insufficient may result in faulty measurement. 

-  Always use the new battery 

-  Do not throw the used battery in the fire. 

-  For  environmental  preservation  dispose  the  used  batteries  according  to  the  regulation  of  each  local 

government 

 

 

3.    Measuring Procedures

 

(1) Press the HOLD/

l

  key.    After the whole area of the display is lit, It is ready to measure.   

* The display mode just before turning off is held.      After replacement of batteries, the display is a

 

Wind 

Velocity Measurement Mode.   

Содержание PC-53D









Отзывы: