Sartorius LP Models, Руководство по эксплуатации

Страница: 70 / 99

70
Additional Functions
Password
You can block access to parameter
settings in the Setup menu and to
the ID-code input function, as well as
to the exact calibration weight, by
assigning a password.
Enter the password by selecting
INPUT
in the Setup menu.
See “Configuring the Balance” for
a detailed description.
Protecting Menu Parameters
In the Setup menu, you can define
whether menu parameters are:
– accessible for changes
(
alterable
,
8 1 1
)
– can be read only (
readable
,
8 1 2
)
Acoustic Signal
An acoustic signal is emitted
when you press a key. When the
key pressed is allowed, the signal
is a single beep tone; when it
is not allowed, this is signaled by
a double beep (key does not initiate
a function). In the Setup menu,
you can configure whether
– the acoustic signal should sound
(
on
,
8 2 1
), or
– the acoustic signal should not
sound (
off
,
8 2 2
)
Blocking the Keys
When you operate the balance via
an on-line computer, it is advisable
that you block the keys on the
display and control unit. In the Setup
menu, you can configure whether
– the keys are active
(
Keys unblocked
,
8 3 1
),
– the keys are blocked
(
Keys blocked
,
8 3 2
), except
for M and e , or
– the alphanumeric keys
are blocked
(
alphanum. blocked
,
8 3 3
).
Universal Switch for Remote Control
You can connect an external
universal switch to the interface port
of your balance (e.g., a foot switch)
for remote control of the functions
listed below. In the Setup menu,
you can configure which function is
to be controlled via remote switch:
– Printing (
Print key funct.
,
8 4 1
)
– Taring
(
Tare key function
,
8 4 2
)
– Calibration
(
CAL key function
,
8 4 3
)
– Function key
(
F key function
,
8 4 4
)
– Delete/cancel
(
CF key function
,
8 4 5
)
– Toggling
(
Toggle key funct.
,
8 4 6
)
Display Backlighting
You can have the display
backlighted for improved readability
of displayed values. In the Setup
menu, you can configure whether the
– display backlighting is on
(
on
,
8 5 1
),
– display backlighting is off
(
off
,
8 5 2
), or
– display backlighting switches off
automatically if there is no change
in the readout for at least 4 minutes
(
Auto off aft. 4 min.
,
8 5 3
)
Power-On Mode
You can configure the balance
so that once a power supply is
connected,
– the balance is turned off
(
Off/on/standby
,
8 6 1
or
Off/on
,
8 6 2
), or
– the balance switches on
automatically (
Auto on
,
8 6 4
)
You can also set the configurations
so that when the balance
is switched off after use, it is
– off – not in balances with
a weighing capacity
≥
16 kg
(
Off/on
,
8 6 2
), or
– in the standby mode
(
Off/on/standby
,
8 6 1
)
When you turn on the balance,
a self-test of the functions is run (test
is displayed; the bar graph is shown)
After the self-test has been
completed, the weighing range
of the balance is displayed (line for
metrological data shows different
maximum values)
Automatic Shutoff
When parameter
8 6 2
is selected
in the Setup menu, you can configure
whether
– the balance will shut off
automatically after 4 minutes
without use
(
After 4 min.
,
8 7 1
), or
– automatic shutoff is deactivated
(
off
,
8 7 2
)