background image

Copyright © 2018, Sargent Manufacturing Company

, an ASSA ABLOY Group company

. All rights reser

ved. 

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

05/31/18

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device 

may not cause harmful interference, and (2) this device must accept any interference received, including interference that 

may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi-

dential installation.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with 

the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the inter-

ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme avec la norme NMB-003 du Canada.

Contains  FCC ID:  U4A-SCSEHF 
Contains  IC:  6982A-SCSEHF 

The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were 

met. This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. 

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)  

this device must accept any interference received, including interference that may cause undesired operation. 
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des 

règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer 

l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui 

peut causer l’opération peu désirée.

Changes or modifications to this unit not expressly approved by the party  
responsible for compliance could void the user’s authority to operate the equipment.

Table of Contents

Warning  ...................................................................................3
General Description .................................................................4
Technical Specifications .........................................................4
Regulatory Specifications .......................................................4
Wiring Diagrams ......................................................................5
Parts Breakdown .....................................................................7
Installation Instructions  .......................................................10
Concealed Door Position Switch Instructions (3287)  ..........16
Mechanical Operational Check .............................................17
Electrical Operational Check .................................................17

Observe precautions for handling electrostatic sensitive devices.

A8239A • 800-810-WIRE (9473) • www.sargentlock.com

3

1

2
3

4

5

6

7

8

9

1

Warning

 

!

Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and 

SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any specific 

situation. When retrofitting any portion of an existing fire rated opening, or specifying and installing a new fire-rated 

opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure compliance 

with all applicable codes and ratings.

10

Содержание SE LP10 7000 Series





















Отзывы: