Sapling SAM Series Скачать руководство пользователя | Manualshive

Страница: 55 / 72

background image

1 2

3 4

55

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com

Double Mount Installation - Square Clock

1) Install the double gang box in the wall or ceiling.
If you are installing the gang box in the wall, leave
at least eleven inches between the top of the
gang box and the ceiling. If you are installing the
gang box in the ceiling, leave at least eleven inches
between the gang box and the wall. The box should
be installed level and plumb with the wall
and ceiling.

3) Detach the mounting plate from the mounting
pole by unscrewing the two screws. Set the screws
and pole aside for later.

2) Run power and communication wiring to the

gang box. See the sections of this manual labeled

“Wiring Information” for additional details,

depending on your system.

If you are using a 2-wire system, pull the
YELLOW and GREEN wires out of
the connectors.

4) Attach the mounting plate to the gang box using
only two of the four long, silver #6-32x1 screws.
With the mounting plate as a guide, use the pencil
to trace the locations of the four larger holes at the
outer corners.

Ceiling

11” Minimum

CHECK YOUR WIRING

The voltage between the white and black wires
should measure 105-126 volts AC in the 115
volt model, 207-253 volts AC in the 230 volt
model, or 21.5-26.5 volts AC in the 24
volt model.

If you are using the 24 volt model, make sure
that the wiring leading to the clock is from an
ISOLATED transformer.

«
...
53
54
55
56
57
...
»

Содержание SAM Series









































































Отзывы:

Нет отзывов

Похожие инструкции для SAM Series

Бренд: Kambrook Страницы: 2

Бренд: Hyundai Страницы: 24

Бренд: Auriol Страницы: 48

Бренд: Jensen Страницы: 22

Бренд: Philips Страницы: 2

Бренд: Qudo Страницы: 10

POWERVALET iW18

Бренд: iHome Страницы: 8

Бренд: TFA Страницы: 2

Travel Soother 20 SI621

Бренд: Sharper Image Страницы: 10

Бренд: Sharper Image Страницы: 20

Бренд: Denver Страницы: 16

Бренд: LEXIBOOK Страницы: 39

Бренд: ADE Страницы: 112

Бренд: RCA Страницы: 5

Бренд: TFA Страницы: 38

Бренд: HKW Страницы: 3

Бренд: Sunbeam Страницы: 32

Бренд: Garden Treasures Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды