manualshive.com logo in svg

Sapling SAM Series, Руководство по установке

Поделиться
Скачать
Sapling SAM Series Скачать руководство пользователя страница 70

70

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA

P. (+1) 215.322.6063 
F. (+1) 215.322.8498
www.sapling-inc.com

Number of Red Flashes

1,2

3,4,5

6,7,8

Error Message

Error detected in second hand. Confirm that hands 
are not hitting each other, then repeat the test.

Error detected in the minute or hour hand. Confirm 
that hands are not hitting each other, then repeat 
the test.

Call tech support. (+1) 215.322.6063

Diagnostic Test #3 - Manufacturing Default (Metal Only)

The purpose of Diagnostic #3 is to bring the clock 
back to 12:00:00 and reset to the manufacturer’s 
default.

Diagnostic #3 may be enabled by holding down the 
diagnostic button for five seconds. If the SAM clock 
is performing this diagnostic, then a green LED on 
the back will flash three times with a five second 
break between each flash. The LED will continue 
to flash green until the diagnostic is complete. The 
clock will confirm that the diagnostic is complete 
when the LED shines a different color.

If the LED is flashing red:

If the LED is a solid green and all of the clock hands are pointing to 12, the test was completed successfully.

At the end of Diagnostic three, the clock hands will be set to 12:00:00. The clock will not resume normal 
operation until the power has been recycled.

Button

LED

Содержание SAM Series









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды